1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
44 # Directory common source filess exist
47 # Directory keyboard dependent files exist
50 # project specific files
51 SRC = keymap_common.c \
57 SRC := keymap_$(KEYMAP).c $(SRC)
59 SRC := keymap_ansi.c $(SRC)
69 # Processor frequency.
70 # This will define a symbol, F_CPU, in all source code files equal to the
71 # processor frequency in Hz. You can then use this symbol in your source code to
72 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
73 # automatically to create a 32-bit value in your source code.
75 # This will be an integer division of F_USB below, as it is sourced by
76 # F_USB after it has run through any CPU prescalers. Note that this value
77 # does not *change* the processor frequency - it should merely be updated to
78 # reflect the processor speed set externally so that the code can use accurate
86 # Target architecture (see library "Board Types" documentation).
89 # Input clock frequency.
90 # This will define a symbol, F_USB, in all source code files equal to the
91 # input clock frequency (before any prescaling is performed) in Hz. This value may
92 # differ from F_CPU if prescaling is used on the latter, and is required as the
93 # raw input clock is fed directly to the PLL sections of the AVR for high speed
94 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
95 # at the end, this will be done automatically to create a 32-bit value in your
98 # If no clock division is performed on the input clock inside the AVR (via the
99 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
102 # Interrupt driven control endpoint task(+60)
103 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
106 # Boot Section Size in *bytes*
108 # Teensy++ halfKay 1024
109 # Atmel DFU loader 4096
110 # LUFA bootloader 4096
112 OPT_DEFS += -DBOOTLOADER_SIZE=4096
116 # comment out to disable the options.
118 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
119 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
120 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
121 CONSOLE_ENABLE = yes # Console for debug(+400)
122 COMMAND_ENABLE = yes # Commands for debug and configuration
123 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
124 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
127 # Optimize size but this may cause error "relocation truncated to fit"
128 #EXTRALDFLAGS = -Wl,--relax
131 VPATH += $(TARGET_DIR)
134 include $(TOP_DIR)/protocol/lufa.mk
135 include $(TOP_DIR)/protocol.mk
136 include $(TOP_DIR)/common.mk
137 include $(TOP_DIR)/rules.mk