1 # Target file name (without extension).
4 # Directory common source filess exist
5 TMK_DIR ?= ../../tmk_core
7 # Directory keyboard dependent files exist
10 # project specific files
18 # atmega32u4 Teensy2.0
19 # atemga32u4 TMK Converter rev.1
20 # atemga32u2 TMK Converter rev.2
23 # Processor frequency.
24 # This will define a symbol, F_CPU, in all source code files equal to the
25 # processor frequency in Hz. You can then use this symbol in your source code to
26 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
27 # automatically to create a 32-bit value in your source code.
29 # This will be an integer division of F_USB below, as it is sourced by
30 # F_USB after it has run through any CPU prescalers. Note that this value
31 # does not *change* the processor frequency - it should merely be updated to
32 # reflect the processor speed set externally so that the code can use accurate
40 # Target architecture (see library "Board Types" documentation).
43 # Input clock frequency.
44 # This will define a symbol, F_USB, in all source code files equal to the
45 # input clock frequency (before any prescaling is performed) in Hz. This value may
46 # differ from F_CPU if prescaling is used on the latter, and is required as the
47 # raw input clock is fed directly to the PLL sections of the AVR for high speed
48 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
49 # at the end, this will be done automatically to create a 32-bit value in your
52 # If no clock division is performed on the input clock inside the AVR (via the
53 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
56 # Interrupt driven control endpoint task(+60)
57 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
60 # Boot Section Size in *bytes*
62 # Teensy++ halfKay 1024
63 # Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
64 # LUFA bootloader 4096
66 BOOTLOADER_SIZE ?= 4096
67 OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
71 # comment out to disable the options.
73 BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
74 MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
75 EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
76 CONSOLE_ENABLE ?= yes # Console for debug(+400)
77 COMMAND_ENABLE ?= yes # Commands for debug and configuration
78 NKRO_ENABLE ?= no # USB Nkey Rollover
79 ADB_MOUSE_ENABLE ?= yes # ADB Mouse support
80 UNIMAP_ENABLE ?= yes # Use unimap
81 ACTIONMAP_ENABLE ?= no # Use 16bit actionmap instead of 8bit keymap
82 KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor
84 # ADB Mice need acceleration for todays much bigger screens.
86 OPT_DEFS += -DADB_MOUSE_MAXACC=$(ADB_MOUSE_MAXACC)
89 # Optimize size but this may cause error "relocation truncated to fit"
90 #EXTRALDFLAGS = -Wl,--relax
96 ifeq (yes,$(strip $(UNIMAP_ENABLE)))
99 ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
100 KEYMAP_FILE = actionmap
106 SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
108 SRC := $(KEYMAP_FILE)_plain.c $(SRC)
113 VPATH += $(TARGET_DIR)
116 include $(TMK_DIR)/protocol/lufa.mk
117 include $(TMK_DIR)/protocol.mk
118 include $(TMK_DIR)/common.mk
119 include $(TMK_DIR)/rules.mk