2 # Makefile for PJRC Teensy
6 # Target file name (without extension).
9 # Directory common source filess exist
10 TMK_DIR = ../../tmk_core
12 # Directory keyboard dependent files exist
15 # keyboard dependent files
19 protocol/serial_uart.c
21 CONFIG_H = config_pjrc.h
24 # MCU name, you MUST set this to match the board you are using
25 # type "make clean" after changing this, so all files will be rebuilt
26 #MCU = at90usb162 # Teensy 1.0
27 MCU = atmega32u4 # Teensy 2.0
28 #MCU = at90usb646 # Teensy++ 1.0
29 #MCU = at90usb1286 # Teensy++ 2.0
32 # Processor frequency.
33 # Normally the first thing your program should do is set the clock prescaler,
34 # so your program will run at the correct speed. You should also set this
35 # variable to same clock speed. The _delay_ms() macro uses this, and many
36 # examples use this variable to calculate timings. Do not add a "UL" here.
40 # Boot Section Size in bytes
42 # Atmel DFU loader 4096
43 # LUFA bootloader 4096
44 OPT_DEFS += -DBOOTLOADER_SIZE=4096
48 # *Comment out* to disable the options.
50 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
51 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
52 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
53 CONSOLE_ENABLE = yes # Console for debug(+400)
54 COMMAND_ENABLE = yes # Commands for debug and configuration
55 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
56 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
60 #---------------- Programming Options --------------------------
62 # Type: avrdude -c ? to get a full listing.
63 AVRDUDE_PROGRAMMER = avr109
64 AVRDUDE_PORT = /dev/ttyACM0
65 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
66 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
68 # Uncomment the following if you want avrdude's erase cycle counter.
69 # Note that this counter needs to be initialized first using -Yn,
71 #AVRDUDE_ERASE_COUNTER = -y
73 # Uncomment the following if you do /not/ wish a verification to be
74 # performed after programming the device.
75 #AVRDUDE_NO_VERIFY = -V
77 # Increase verbosity level. Please use this when submitting bug
78 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
79 # to submit bug reports.
80 #AVRDUDE_VERBOSE = -v -v
82 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
83 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
84 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
85 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
86 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
88 #PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
89 #PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
90 PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
94 VPATH += $(TARGET_DIR)
98 include $(TMK_DIR)/protocol/pjrc.mk
99 include $(TMK_DIR)/protocol.mk
100 include $(TMK_DIR)/common.mk
101 include $(TMK_DIR)/rules.mk