1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
44 # Directory common source filess exist
47 # Directory keyboard dependent files exist
51 # List C source files here. (C dependencies are automatically generated.)
52 SRC += keymap_common.c \
58 SRC := keymap_$(KEYMAP).c $(SRC)
60 SRC := keymap_hhkb.c $(SRC)
69 # TMK Alt Controller or PJRC Teensy 2.0
72 # Processor frequency.
73 # This will define a symbol, F_CPU, in all source code files equal to the
74 # processor frequency in Hz. You can then use this symbol in your source code to
75 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
76 # automatically to create a 32-bit value in your source code.
78 # This will be an integer division of F_USB below, as it is sourced by
79 # F_USB after it has run through any CPU prescalers. Note that this value
80 # does not *change* the processor frequency - it should merely be updated to
81 # reflect the processor speed set externally so that the code can use accurate
89 # Target architecture (see library "Board Types" documentation).
92 # Input clock frequency.
93 # This will define a symbol, F_USB, in all source code files equal to the
94 # input clock frequency (before any prescaling is performed) in Hz. This value may
95 # differ from F_CPU if prescaling is used on the latter, and is required as the
96 # raw input clock is fed directly to the PLL sections of the AVR for high speed
97 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
98 # at the end, this will be done automatically to create a 32-bit value in your
101 # If no clock division is performed on the input clock inside the AVR (via the
102 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
105 # Interrupt driven control endpoint task
106 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
109 # Boot Section Size in *bytes*
111 # Teensy++ halfKay 1024
112 # Atmel DFU loader 4096 (TMK Alt Controller)
113 # LUFA bootloader 4096
115 OPT_DEFS += -DBOOTLOADER_SIZE=4096
119 # comment out to disable the options.
121 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
122 MOUSEKEY_ENABLE = yes # Mouse keys
123 EXTRAKEY_ENABLE = yes # Audio control and System control
124 CONSOLE_ENABLE = yes # Console for debug
125 COMMAND_ENABLE = yes # Commands for debug and configuration
126 NKRO_ENABLE = yes # USB Nkey Rollover
127 KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
131 VPATH += $(TARGET_DIR)
134 include $(TOP_DIR)/protocol/lufa.mk
135 include $(TOP_DIR)/common.mk
136 include $(TOP_DIR)/rules.mk
138 debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
141 debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT