1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
42 TARGET = lightpad_lufa
44 # Directory common source filess exist
47 # Directory keyboard dependent files exist
50 # List C source files here. (C dependencies are automatically generated.)
61 # Processor frequency.
62 # This will define a symbol, F_CPU, in all source code files equal to the
63 # processor frequency in Hz. You can then use this symbol in your source code to
64 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
65 # automatically to create a 32-bit value in your source code.
67 # This will be an integer division of F_USB below, as it is sourced by
68 # F_USB after it has run through any CPU prescalers. Note that this value
69 # does not *change* the processor frequency - it should merely be updated to
70 # reflect the processor speed set externally so that the code can use accurate
77 # Target architecture (see library "Board Types" documentation).
80 # Input clock frequency.
81 # This will define a symbol, F_USB, in all source code files equal to the
82 # input clock frequency (before any prescaling is performed) in Hz. This value may
83 # differ from F_CPU if prescaling is used on the latter, and is required as the
84 # raw input clock is fed directly to the PLL sections of the AVR for high speed
85 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
86 # at the end, this will be done automatically to create a 32-bit value in your
89 # If no clock division is performed on the input clock inside the AVR (via the
90 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
94 # comment out to disable the options.
96 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
97 #MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
98 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
99 #CONSOLE_ENABLE = yes # Console for debug(+400)
100 #COMMAND_ENABLE = yes # Commands for debug and configuration
101 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
102 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
103 BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
105 # Boot Section Size in bytes
107 # Atmel DFU loader 4096
108 # LUFA bootloader 4096
109 OPT_DEFS += -DBOOTLOADER_SIZE=4096
112 VPATH += $(TARGET_DIR)
115 include $(TOP_DIR)/protocol/lufa.mk
116 include $(TOP_DIR)/common.mk
117 include $(TOP_DIR)/rules.mk