tmk_core/protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h

   1 /* Copyright (C) 2015 Andrew J. Kroll
   2    and
   3    Circuits At Home, LTD. All rights reserved.
   4
   5 This software may be distributed and modified under the terms of the GNU
   6 General Public License version 2 (GPL2) as published by the Free Software
   7 Foundation and appearing in the file GPL2.TXT included in the packaging of
   8 this file. Please note that GPL2 Section 2[b] requires that all works based
   9 on this software must also be made publicly available under the terms of
  10 the GPL2 ("Copyleft").
  11
  12 Contact information
  13 -------------------
  14
  15 Circuits At Home, LTD
  16 Web      :  http://www.circuitsathome.com
  17 e-mail   :  support@circuitsathome.com
  18  */
  19 #if !defined(__CDC_XR21B1411_H__)
  20 #define __CDC_XR21B1411_H__
  21
  22 #include "cdcacm.h"
  23
  24 #define XR_REG_CUSTOM_DRIVER                    (0x020DU) // DRIVER SELECT
  25 #define XR_REG_CUSTOM_DRIVER_ACTIVE             (0x0001U) // 0: CDC 1: CUSTOM
  26
  27 #define XR_REG_ACM_FLOW_CTL                     (0x0216U) // FLOW CONTROL REGISTER CDCACM MODE
  28 #define XR_REG_FLOW_CTL                         (0x0C06U) // FLOW CONTROL REGISTER CUSTOM MODE
  29 #define XR_REG_FLOW_CTL_HALF_DPLX               (0x0008U) // 0:FULL DUPLEX 1:HALF DUPLEX
  30 #define XR_REG_FLOW_CTL_MODE_MASK               (0x0007U) // MODE BITMASK
  31 #define XR_REG_FLOW_CTL_NONE                    (0x0000U) // NO FLOW CONTROL
  32 #define XR_REG_FLOW_CTL_HW                      (0x0001U) // HARDWARE FLOW CONTROL
  33 #define XR_REG_FLOW_CTL_SW                      (0x0002U) // SOFTWARE FLOW CONTROL
  34 #define XR_REG_FLOW_CTL_MMMRX                   (0x0003U) // MULTIDROP RX UPON ADDRESS MATCH
  35 #define XR_REG_FLOW_CTL_MMMRXTX                 (0x0004U) // MULTIDROP RX/TX UPON ADDRESS MATCH
  36
  37 #define XR_REG_ACM_GPIO_MODE                    (0x0217U) // GPIO MODE REGISTER IN CDCACM MODE
  38 #define XR_REG_GPIO_MODE                        (0x0C0CU) // GPIO MODE REGISTER IN CUSTOM MODE
  39 #define XR_REG_GPIO_MODE_GPIO                   (0x0000U) // ALL GPIO PINS ACM PROGRAMMABLE
  40 #define XR_REG_GPIO_MODE_FC_RTSCTS              (0x0001U) // AUTO RTSCTS HW FC (GPIO 4/5)
  41 #define XR_REG_GPIO_MODE_FC_DTRDSR              (0x0002U) // AUTO DTRDSR HW FC (GPIO 2/3)
  42 #define XR_REG_GPIO_MODE_ATE                    (0x0003U) // AUTO TRANSCEIVER ENABLE DURING TX (GPIO 5)
  43 #define XR_REG_GPIO_MODE_ATE_ADDRESS            (0x0004U) // AUTO TRANSCEIVER ENABLE ON ADDRESS MATCH (GPIO 5)
  44
  45 #define XR_REG_ACM_GPIO_DIR                     (0x0218U) // GPIO DIRECTION REGISTER CDCACM MODE, 0:IN 1:OUT
  46 #define XR_REG_GPIO_DIR                         (0x0C0DU) // GPIO DIRECTION REGISTER CUSTOM MODE, 0:IN 1:OUT
  47
  48 #define XR_REG_ACM_GPIO_INT                     (0x0219U) // GPIO PIN CHANGE INTERRUPT ENABLE CDCACM MODE, 0: ENABLED 1: DISABLED
  49 #define XR_REG_GPIO_INT                         (0x0C11U) // GPIO PIN CHANGE INTERRUPT ENABLE CUSTOM MODE, 0: ENABLED 1: DISABLED
  50 #define XR_REG_GPIO_MASK                        (0x001FU) // GPIO REGISTERS BITMASK
  51
  52 #define XR_REG_UART_ENABLE                      (0x0C00U) // UART I/O ENABLE REGISTER
  53 #define XR_REG_UART_ENABLE_RX                   (0x0002U) // 0:DISABLED 1:ENABLED
  54 #define XR_REG_UART_ENABLE_TX                   (0x0001U) // 0:DISABLED 1:ENABLED
  55
  56 #define XR_REG_ERROR_STATUS                     (0x0C09U) // ERROR STATUS REGISTER
  57 #define XR_REG_ERROR_STATUS_MASK                (0x00F8U) // ERROR STATUS BITMASK
  58 #define XR_REG_ERROR_STATUS_ERROR               (0x0078U) // ERROR STATUS ERROR BITMASK
  59 #define XR_REG_ERROR_STATUS_BREAK               (0x0008U) // BREAK ERROR HAS BEEN DETECTED
  60 #define XR_REG_ERROR_STATUS_FRAME               (0x0010U) // FRAMING ERROR HAS BEEN DETECTED
  61 #define XR_REG_ERROR_STATUS_PARITY              (0x0020U) // PARITY ERROR HAS BEEN DETECTED
  62 #define XR_REG_ERROR_STATUS_OVERRUN             (0x0040U) // RX OVERRUN ERROR HAS BEEN DETECTED
  63 #define XR_REG_ERROR_STATUS_BREAK_STATUS        (0x0080U) // BREAK CONDITION IS CURRENTLY BEING DETECTED
  64
  65 #define XR_REG_TX_BREAK                         (0x0C0AU) // TRANSMIT BREAK. 0X0001-0XFFE TIME IN MS, 0X0000 STOP, 0X0FFF BREAK ON
  66
  67 #define XR_REG_XCVR_EN_DELAY                    (0x0C0BU) // TURN-ARROUND DELAY IN BIT-TIMES 0X0000-0X000F
  68
  69 #define XR_REG_GPIO_SET                         (0x0C0EU) // 1:SET GPIO PIN
  70
  71 #define XR_REG_GPIO_CLR                         (0x0C0FU) // 1:CLEAR GPIO PIN
  72
  73 #define XR_REG_GPIO_STATUS                      (0x0C10U) // READ GPIO PINS
  74
  75 #define XR_REG_CUSTOMISED_INT                   (0x0C12U) // 0:STANDARD 1:CUSTOM SEE DATA SHEET
  76
  77 #define XR_REG_PIN_PULLUP_ENABLE                (0x0C14U) // 0:DISABLE 1:ENABLE, BITS 0-5:GPIO, 6:RX 7:TX
  78
  79 #define XR_REG_PIN_PULLDOWN_ENABLE              (0x0C15U) // 0:DISABLE 1:ENABLE, BITS 0-5:GPIO, 6:RX 7:TX
  80
  81 #define XR_REG_LOOPBACK                         (0x0C16U) // 0:DISABLE 1:ENABLE, SEE DATA SHEET
  82
  83 #define XR_REG_RX_FIFO_LATENCY                  (0x0CC2U) // FIFO LATENCY REGISTER
  84 #define XR_REG_RX_FIFO_LATENCY_ENABLE           (0x0001U) //
  85
  86 #define XR_REG_WIDE_MODE                        (0x0D02U)
  87 #define XR_REG_WIDE_MODE_ENABLE                 (0x0001U)
  88
  89 #define XR_REG_XON_CHAR                         (0x0C07U)
  90 #define XR_REG_XOFF_CHAR                        (0x0C08U)
  91
  92 #define XR_REG_TX_FIFO_RESET                    (0x0C80U) // 1: RESET, SELF-CLEARING
  93 #define XR_REG_TX_FIFO_COUNT                    (0x0C81U) // READ-ONLY
  94 #define XR_REG_RX_FIFO_RESET                    (0x0CC0U) // 1: RESET, SELF-CLEARING
  95 #define XR_REG_RX_FIFO_COUNT                    (0x0CC1U) // READ-ONLY
  96
  97 #define XR_WRITE_REQUEST_TYPE                   (0x40U)
  98
  99 #define XR_READ_REQUEST_TYPE                    (0xC0U)
 100
 101 #define XR_MAX_ENDPOINTS                        4
 102
 103 class XR21B1411 : public ACM {
 104 protected:
 105
 106 public:
 107         XR21B1411(USB *pusb, CDCAsyncOper *pasync);
 108
 109         /**
 110          * Used by the USB core to check what this driver support.
 111          * @param  vid The device's VID.
 112          * @param  pid The device's PID.
 113          * @return     Returns true if the device's VID and PID matches this driver.
 114          */
 115         virtual bool VIDPIDOK(uint16_t vid, uint16_t pid) {
 116                 return (((vid == 0x2890U) && (pid == 0x0201U)) || ((vid == 0x04e2U) && (pid == 0x1411U)));
 117         };
 118
 119         uint8_t Init(uint8_t parent, uint8_t port, bool lowspeed);
 120
 121         virtual tty_features enhanced_features(void) {
 122                 tty_features rv;
 123                 rv.enhanced = true;
 124                 rv.autoflow_RTS = true;
 125                 rv.autoflow_DSR = true;
 126                 rv.autoflow_XON = true;
 127                 rv.half_duplex = true;
 128                 rv.wide = true;
 129                 return rv;
 130         };
 131
 132         uint8_t read_register(uint16_t reg, uint16_t *val) {
 133                 return (pUsb->ctrlReq(bAddress, 0, XR_READ_REQUEST_TYPE, 1, 0, 0, reg, 2, 2, (uint8_t *)val, NULL));
 134         }
 135
 136         uint8_t write_register(uint16_t reg, uint16_t val) {
 137                 return (pUsb->ctrlReq(bAddress, 0, XR_WRITE_REQUEST_TYPE, 0, BGRAB0(val), BGRAB1(val), reg, 0, 0, NULL, NULL));
 138         }
 139
 140
 141         ////////////////////////////////////////////////////////////////////////
 142         // The following methods set the CDC-ACM defaults.
 143         ////////////////////////////////////////////////////////////////////////
 144
 145         virtual void autoflowRTS(bool s) {
 146                 uint16_t val;
 147                 uint8_t rval;
 148                 rval = read_register(XR_REG_ACM_FLOW_CTL, &val);
 149                 if(!rval) {
 150                         if(s) {
 151                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 152                                 val |= XR_REG_FLOW_CTL_HW;
 153                         } else {
 154                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 155                         }
 156                         rval = write_register(XR_REG_ACM_FLOW_CTL, val);
 157                         if(!rval) {
 158                                 rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO);
 159                                 if(!rval) {
 160                                         // ACM commands apply the new settings.
 161                                         LINE_CODING LCT;
 162                                         rval = GetLineCoding(&LCT);
 163                                         if(!rval) {
 164                                                 rval = SetLineCoding(&LCT);
 165                                                 if(!rval) {
 166                                                         _enhanced_status.autoflow_XON = false;
 167                                                         _enhanced_status.autoflow_DSR = false;
 168                                                         _enhanced_status.autoflow_RTS = s;
 169                                                 }
 170                                         }
 171                                 }
 172                         }
 173                 }
 174         };
 175
 176         virtual void autoflowDSR(bool s) {
 177                 uint16_t val;
 178                 uint8_t rval;
 179                 rval = read_register(XR_REG_ACM_FLOW_CTL, &val);
 180                 if(!rval) {
 181                         if(s) {
 182                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 183                                 val |= XR_REG_FLOW_CTL_HW;
 184                         } else {
 185                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 186                         }
 187                         rval = write_register(XR_REG_ACM_FLOW_CTL, val);
 188                         if(!rval) {
 189                                 if(s) {
 190                                         rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_FC_DTRDSR);
 191                                 } else {
 192                                         rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO);
 193                                 }
 194                                 if(!rval) {
 195                                         // ACM commands apply the new settings.
 196                                         LINE_CODING LCT;
 197                                         rval = GetLineCoding(&LCT);
 198                                         if(!rval) {
 199                                                 rval = SetLineCoding(&LCT);
 200                                                 if(!rval) {
 201                                                         _enhanced_status.autoflow_XON = false;
 202                                                         _enhanced_status.autoflow_RTS = false;
 203                                                         _enhanced_status.autoflow_DSR = s;
 204                                                 }
 205                                         }
 206                                 }
 207                         }
 208                 }
 209         };
 210
 211         virtual void autoflowXON(bool s) {
 212                 // NOTE: hardware defaults to the normal XON/XOFF
 213                 uint16_t val;
 214                 uint8_t rval;
 215                 rval = read_register(XR_REG_ACM_FLOW_CTL, &val);
 216                 if(!rval) {
 217                         if(s) {
 218                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 219                                 val |= XR_REG_FLOW_CTL_SW;
 220                         } else {
 221                                 val &= XR_REG_FLOW_CTL_HALF_DPLX;
 222                         }
 223                         rval = write_register(XR_REG_ACM_FLOW_CTL, val);
 224                         if(!rval) {
 225                                 rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO);
 226                                 if(!rval) {
 227                                         // ACM commands apply the new settings.
 228                                         LINE_CODING LCT;
 229                                         rval = GetLineCoding(&LCT);
 230                                         if(!rval) {
 231                                                 rval = SetLineCoding(&LCT);
 232                                                 if(!rval) {
 233                                                         _enhanced_status.autoflow_RTS = false;
 234                                                         _enhanced_status.autoflow_DSR = false;
 235                                                         _enhanced_status.autoflow_XON = s;
 236                                                 }
 237                                         }
 238                                 }
 239                         }
 240                 }
 241         };
 242
 243         virtual void half_duplex(bool s) {
 244                 uint16_t val;
 245                 uint8_t rval;
 246                 rval = read_register(XR_REG_ACM_FLOW_CTL, &val);
 247                 if(!rval) {
 248                         if(s) {
 249                                 val |= XR_REG_FLOW_CTL_HALF_DPLX;
 250                         } else {
 251                                 val &= XR_REG_FLOW_CTL_MODE_MASK;
 252                         }
 253                         rval = write_register(XR_REG_ACM_FLOW_CTL, val);
 254                         if(!rval) {
 255                                 // ACM commands apply the new settings.
 256                                 LINE_CODING LCT;
 257                                 rval = GetLineCoding(&LCT);
 258                                 if(!rval) {
 259                                         rval = SetLineCoding(&LCT);
 260                                         if(!rval) {
 261                                                 _enhanced_status.half_duplex = s;
 262                                         }
 263                                 }
 264                         }
 265                 }
 266         };
 267
 268
 269
 270 };
 271
 272 #endif // __CDCPROLIFIC_H__