/**
******************************************************************************
* @file stm32f1xx_hal_rcc_ex.c
* @author MCD Application Team
* @version V1.0.0
* @date 15-December-2014
* @brief Extended RCC HAL module driver.
*
* This file provides firmware functions to manage the following
* functionalities RCC extension peripheral:
* + Extended Peripheral Control functions
*
******************************************************************************
* @attention
*
*
© COPYRIGHT(c) 2014 STMicroelectronics
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal.h"
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
#ifdef HAL_RCC_MODULE_ENABLED
/** @defgroup RCCEx RCCEx
* @brief RCC Extension HAL module driver
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup RCCEx_Private_Constants RCCEx Private Constants
* @{
*/
#define PLL2_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
/* Alias word address of PLL2ON bit */
#define PLL2ON_BITNUMBER POSITION_VAL(RCC_CR_PLL2ON)
#define CR_PLL2ON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (PLL2ON_BITNUMBER * 4)))
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/** @defgroup RCCEx_Private_Macros RCCEx Private Macros
* @{
*/
/**
* @}
*/
/** @defgroup RCCEx_Private_Macros RCCEx Private Macros
* @{
*/
/**
* @}
*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/**
* @}
*/
/** @addtogroup RCC
* @{
*/
/** @addtogroup RCC_Exported_Functions
* @{
*/
#if defined(STM32F105xC) || defined(STM32F107xC) || defined (STM32F100xB) || defined (STM32F100xE)
/** @addtogroup RCC_Exported_Functions_Group1
* @{
*/
/**
* @brief Resets the RCC clock configuration to the default reset state.
* @note The default reset state of the clock configuration is given below:
* - HSI ON and used as system clock source
* - HSE and PLL OFF
* - AHB, APB1 and APB2 prescaler set to 1.
* - CSS and MCO1 OFF
* - All interrupts disabled
* @note This function doesn't modify the configuration of the
* - Peripheral clocks
* - LSI, LSE and RTC clocks
* @retval None
*/
void HAL_RCC_DeInit(void)
{
/* Switch SYSCLK to HSI */
CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW);
/* Reset HSEON, CSSON, & PLLON bits */
CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_CSSON | RCC_CR_PLLON);
/* Reset HSEBYP bit */
CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP);
/* Reset CFGR register */
CLEAR_REG(RCC->CFGR);
/* Set HSITRIM bits to the reset value */
MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, ((uint32_t)0x10 << POSITION_VAL(RCC_CR_HSITRIM)));
/* Reset CFGR2 register */
CLEAR_REG(RCC->CFGR2);
/* Disable all interrupts */
CLEAR_REG(RCC->CIR);
}
/**
* @}
*/
#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */
#if defined(STM32F105xC) || defined(STM32F107xC)
/** @addtogroup RCC_Exported_Functions_Group1
* @{
*/
/**
* @brief Initializes the RCC Oscillators according to the specified parameters in the
* RCC_OscInitTypeDef.
* @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that
* contains the configuration information for the RCC Oscillators.
* @note The PLL is not disabled when used as system clock.
* @note The PLL is not disabled when USB OTG FS clock is enabled (specific to devices with USB FS)
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
{
uint32_t tickstart = 0;
/* Check the parameters */
assert_param(RCC_OscInitStruct != NULL);
assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType));
/*------------------------------- HSE Configuration ------------------------*/
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE)
{
/* Check the parameters */
assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState));
/* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE)
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE)))
{
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState != RCC_HSE_ON) && (RCC_OscInitStruct->HSEState != RCC_HSE_BYPASS))
{
return HAL_ERROR;
}
}
else
{
/* Reset HSEON and HSEBYP bits before configuring the HSE --------------*/
__HAL_RCC_HSE_CONFIG(RCC_HSE_OFF);
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till HSE is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Set the new HSE configuration ---------------------------------------*/
__HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState);
/* Check the HSE State */
if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF)
{
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till HSE is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till HSE is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
}
/*----------------------------- HSI Configuration --------------------------*/
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI)
{
/* Check the parameters */
assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState));
assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue));
/* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI)
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI_DIV2)))
{
/* When HSI is used as system clock it will not disabled */
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON))
{
return HAL_ERROR;
}
/* Otherwise, just the calibration is allowed */
else
{
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
}
}
else
{
/* Check the HSI State */
if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF)
{
/* Enable the Internal High Speed oscillator (HSI). */
__HAL_RCC_HSI_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till HSI is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
}
else
{
/* Disable the Internal High Speed oscillator (HSI). */
__HAL_RCC_HSI_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till HSI is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
}
/*------------------------------ LSI Configuration -------------------------*/
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI)
{
/* Check the parameters */
assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState));
/* Check the LSI State */
if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF)
{
/* Enable the Internal Low Speed oscillator (LSI). */
__HAL_RCC_LSI_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till LSI is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* To have a fully stabilized clock in the specified range, a software temporization of 1ms
should be added.*/
HAL_Delay(1);
}
else
{
/* Disable the Internal Low Speed oscillator (LSI). */
__HAL_RCC_LSI_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till LSI is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
/*------------------------------ LSE Configuration -------------------------*/
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)
{
/* Check the parameters */
assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState));
/* Enable Power Clock*/
__HAL_RCC_PWR_CLK_ENABLE();
/* Enable write access to Backup domain */
SET_BIT(PWR->CR, PWR_CR_DBP);
/* Wait for Backup domain Write protection disable */
tickstart = HAL_GetTick();
while((PWR->CR & PWR_CR_DBP) == RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Reset LSEON and LSEBYP bits before configuring the LSE ----------------*/
__HAL_RCC_LSE_CONFIG(RCC_LSE_OFF);
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till LSE is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Set the new LSE configuration -----------------------------------------*/
__HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState);
/* Check the LSE State */
if((RCC_OscInitStruct->LSEState) == RCC_LSE_ON)
{
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till LSE is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till LSE is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
/*-------------------------------- PLL2 Configuration -----------------------*/
/* Check the parameters */
assert_param(IS_RCC_PLL2(RCC_OscInitStruct->PLL2.PLL2State));
if ((RCC_OscInitStruct->PLL2.PLL2State) != RCC_PLL2_NONE)
{
/* This bit can not be cleared if the PLL2 clock is used indirectly as system
clock (i.e. it is used as PLL clock entry that is used as system clock). */
if((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \
(__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \
((READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2))
{
return HAL_ERROR;
}
else
{
if((RCC_OscInitStruct->PLL2.PLL2State) == RCC_PLL2_ON)
{
/* Check the parameters */
assert_param(IS_RCC_PLL2_MUL(RCC_OscInitStruct->PLL2.PLL2MUL));
assert_param(IS_RCC_HSE_PREDIV2(RCC_OscInitStruct->PLL2.HSEPrediv2Value));
/* Prediv2 can be written only when the PLLI2S is disabled. */
/* Return an error only if new value is different from the programmed value */
if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLL3ON) && \
(__HAL_RCC_HSE_GET_PREDIV2() != RCC_OscInitStruct->PLL2.HSEPrediv2Value))
{
return HAL_ERROR;
}
/* Disable the main PLL2. */
__HAL_RCC_PLL2_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Configure the HSE prediv2 factor --------------------------------*/
__HAL_RCC_HSE_PREDIV2_CONFIG(RCC_OscInitStruct->PLL2.HSEPrediv2Value);
/* Configure the main PLL2 multiplication factors. */
__HAL_RCC_PLL2_CONFIG(RCC_OscInitStruct->PLL2.PLL2MUL);
/* Enable the main PLL2. */
__HAL_RCC_PLL2_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* Set PREDIV1 source to HSE */
CLEAR_BIT(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC);
/* Disable the main PLL2. */
__HAL_RCC_PLL2_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
}
/*-------------------------------- PLL Configuration -----------------------*/
/* Check the parameters */
assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState));
if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE)
{
/* Check if the PLL is used as system clock or not */
if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK)
{
if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON)
{
/* Check the parameters */
assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource));
assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL));
/* Disable the main PLL. */
__HAL_RCC_PLL_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Configure the HSE prediv1 factor and source --------------------------------*/
/* It can be written only when the PLL is disabled. Not used in PLL source is different than HSE */
if(RCC_OscInitStruct->PLL.PLLSource == RCC_PLLSOURCE_HSE)
{
/* Check the parameter */
assert_param(IS_RCC_PREDIV1_SOURCE(RCC_OscInitStruct->Prediv1Source));
assert_param(IS_RCC_HSE_PREDIV(RCC_OscInitStruct->HSEPredivValue));
/* Set PREDIV1 source */
SET_BIT(RCC->CFGR2, RCC_OscInitStruct->Prediv1Source);
/* Set PREDIV1 Value */
__HAL_RCC_HSE_PREDIV_CONFIG(RCC_OscInitStruct->HSEPredivValue);
}
/* Configure the main PLL clock source and multiplication factors. */
__HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource,
RCC_OscInitStruct->PLL.PLLMUL);
/* Enable the main PLL. */
__HAL_RCC_PLL_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* Disable the main PLL. */
__HAL_RCC_PLL_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
else
{
return HAL_ERROR;
}
}
return HAL_OK;
}
/**
* @}
*/
#endif /* STM32F105xC STM32F107xC */
#if defined(STM32F101x6) || defined(STM32F101xB) || defined(STM32F101xE) || defined(STM32F101xG) || \
defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || \
defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
/** @addtogroup RCC_Exported_Functions_Group1
* @{
*/
/**
* @brief Initializes the CPU, AHB and APB busses clocks according to the specified
* parameters in the RCC_ClkInitStruct.
* @param RCC_ClkInitStruct: pointer to an RCC_OscInitTypeDef structure that
* contains the configuration information for the RCC peripheral.
* @param FLatency: FLASH Latency
* This parameter can be one of the following values:
* @arg FLASH_LATENCY_0: FLASH 0 Latency cycle
*
* @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
* and updated by HAL_RCC_GetHCLKFreq() function called within this function
*
* @note The HSI is used (enabled by hardware) as system clock source after
* startup from Reset, wake-up from STOP and STANDBY mode, or in case
* of failure of the HSE used directly or indirectly as system clock
* (if the Clock Security System CSS is enabled).
*
* @note A switch from one clock source to another occurs only if the target
* clock source is ready (clock stable after startup delay or PLL locked).
* If a clock source which is not yet ready is selected, the switch will
* occur when the clock source will be ready.
* You can use HAL_RCC_GetClockConfig() function to know which clock is
* currently used as system clock source.
* @retval None
*/
HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency)
{
uint32_t tickstart = 0;
/* Check the parameters */
assert_param(RCC_ClkInitStruct != NULL);
assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType));
assert_param(IS_FLASH_LATENCY(FLatency));
/* To correctly read data from FLASH memory, the number of wait states (LATENCY)
must be correctly programmed according to the frequency of the CPU clock
(HCLK) of the device. */
/* Increasing the CPU frequency */
if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY))
{
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
__HAL_FLASH_SET_LATENCY(FLatency);
/* Check that the new number of wait states is taken into account to access the Flash
memory by reading the FLASH_ACR register */
if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency)
{
return HAL_ERROR;
}
/*-------------------------- HCLK Configuration --------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
{
assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
}
/*------------------------- SYSCLK Configuration ---------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
{
assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
/* HSE is selected as System Clock Source */
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
{
/* Check the HSE ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
{
return HAL_ERROR;
}
}
/* PLL is selected as System Clock Source */
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
{
/* Check the PLL ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
{
return HAL_ERROR;
}
}
/* HSI is selected as System Clock Source */
else
{
/* Check the HSI ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
{
return HAL_ERROR;
}
}
MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource);
/* Get Start Tick*/
tickstart = HAL_GetTick();
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
}
/* Decreasing the CPU frequency */
else
{
/*-------------------------- HCLK Configuration --------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
{
assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
}
/*------------------------- SYSCLK Configuration -------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
{
assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
/* HSE is selected as System Clock Source */
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
{
/* Check the HSE ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
{
return HAL_ERROR;
}
}
/* PLL is selected as System Clock Source */
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
{
/* Check the PLL ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
{
return HAL_ERROR;
}
}
/* HSI is selected as System Clock Source */
else
{
/* Check the HSI ready flag */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
{
return HAL_ERROR;
}
}
MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource);
/* Get Start Tick*/
tickstart = HAL_GetTick();
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI)
{
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
}
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
__HAL_FLASH_SET_LATENCY(FLatency);
/* Check that the new number of wait states is taken into account to access the Flash
memory by reading the FLASH_ACR register */
if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency)
{
return HAL_ERROR;
}
}
/*-------------------------- PCLK1 Configuration ---------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
{
assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider));
MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider);
}
/*-------------------------- PCLK2 Configuration ---------------------------*/
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
{
assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider));
MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3));
}
/* Configure the source of time base considering new system clocks settings*/
HAL_InitTick (TICK_INT_PRIORITY);
return HAL_OK;
}
/**
* @}
*/
#endif /* STM32F101x6 || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */
#if defined(STM32F105xC) || defined(STM32F107xC)
/** @addtogroup RCC_Exported_Functions_Group2
* @{
*/
/**
* @brief Returns the SYSCLK frequency
*
* @note The system frequency computed by this function is not the real
* frequency in the chip. It is calculated based on the predefined
* constant and the selected clock source:
* @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
* @note If SYSCLK source is HSE, function returns values based on HSE_VALUE
* divided by PREDIV factor(**)
* @note If SYSCLK source is PLL, function returns values based on HSE_VALUE
* divided by PREDIV factor(**) or HSI_VALUE(*) multiplied by the PLL factor.
* @note (*) HSI_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value
* 8 MHz).
* @note (**) HSE_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value
* 8 MHz), user has to ensure that HSE_VALUE is same as the real
* frequency of the crystal used. Otherwise, this function may
* have wrong result.
*
* @note The result of this function could be not correct when using fractional
* value for HSE crystal.
*
* @note This function can be used by the user application to compute the
* baudrate for the communication peripherals or configure other parameters.
*
* @note Each time SYSCLK changes, this function must be called to update the
* right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
*
*
* @retval SYSCLK frequency
*/
uint32_t HAL_RCC_GetSysClockFreq(void)
{
const uint8_t aPLLMULFactorTable[12] = {0, 0, 4, 5, 6, 7, 8, 9, 0, 0, 0, 13};
const uint8_t aPredivFactorTable[16] = { 1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12, 13, 14, 15, 16};
uint32_t tmp_reg = 0, prediv1 = 0, pllclk = 0, pllmul = 0;
uint32_t sysclockfreq = 0;
uint32_t prediv2 = 0, pll2mul = 0;
tmp_reg = RCC->CFGR;
/* Get SYSCLK source -------------------------------------------------------*/
switch (tmp_reg & RCC_CFGR_SWS)
{
case RCC_CFGR_SWS_HSE: /* HSE used as system clock */
{
sysclockfreq = HSE_VALUE;
break;
}
case RCC_CFGR_SWS_PLL: /* PLL used as system clock */
{
pllmul = aPLLMULFactorTable[(uint32_t)(tmp_reg & RCC_CFGR_PLLMULL) >> POSITION_VAL(RCC_CFGR_PLLMULL)];
if ((tmp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2)
{
prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> POSITION_VAL(RCC_CFGR2_PREDIV1)];
if(HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC))
{
/* PLL2 selected as Prediv1 source */
/* PLLCLK = PLL2CLK / PREDIV1 * PLLMUL with PLL2CLK = HSE/PREDIV2 * PLL2MUL */
prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> POSITION_VAL(RCC_CFGR2_PREDIV2)) + 1;
pll2mul = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> POSITION_VAL(RCC_CFGR2_PLL2MUL)) + 2;
pllclk = (uint32_t)((((HSE_VALUE / prediv2) * pll2mul) / prediv1) * pllmul);
}
else
{
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */
pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul);
}
/* If PLLMUL was set to 13 means that it was to cover the case PLLMUL 6.5 (avoid using float) */
/* In this case need to divide pllclk by 2 */
if (pllmul == aPLLMULFactorTable[(uint32_t)(RCC_CFGR_PLLMULL6_5) >> POSITION_VAL(RCC_CFGR_PLLMULL)])
{
pllclk = pllclk / 2;
}
}
else
{
/* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */
pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul);
}
sysclockfreq = pllclk;
break;
}
case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */
default: /* HSI used as system clock */
{
sysclockfreq = HSI_VALUE;
break;
}
}
return sysclockfreq;
}
/**
* @brief Configures the RCC_OscInitStruct according to the internal
* RCC configuration registers.
* @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that
* will be configured.
* @retval None
*/
void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
{
/* Check the parameters */
assert_param(RCC_OscInitStruct != NULL);
/* Set all possible values for the Oscillator type parameter ---------------*/
RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI \
| RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI;
/* Get the Prediv1 source --------------------------------------------------*/
RCC_OscInitStruct->Prediv1Source = READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC);
/* Get the HSE configuration -----------------------------------------------*/
if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP)
{
RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS;
}
else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON)
{
RCC_OscInitStruct->HSEState = RCC_HSE_ON;
}
else
{
RCC_OscInitStruct->HSEState = RCC_HSE_OFF;
}
RCC_OscInitStruct->HSEPredivValue = __HAL_RCC_HSE_GET_PREDIV();
/* Get the HSI configuration -----------------------------------------------*/
if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION)
{
RCC_OscInitStruct->HSIState = RCC_HSI_ON;
}
else
{
RCC_OscInitStruct->HSIState = RCC_HSI_OFF;
}
RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> POSITION_VAL(RCC_CR_HSITRIM));
/* Get the LSE configuration -----------------------------------------------*/
if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP)
{
RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS;
}
else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON)
{
RCC_OscInitStruct->LSEState = RCC_LSE_ON;
}
else
{
RCC_OscInitStruct->LSEState = RCC_LSE_OFF;
}
/* Get the LSI configuration -----------------------------------------------*/
if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION)
{
RCC_OscInitStruct->LSIState = RCC_LSI_ON;
}
else
{
RCC_OscInitStruct->LSIState = RCC_LSI_OFF;
}
/* Get the PLL configuration -----------------------------------------------*/
if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON)
{
RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON;
}
else
{
RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF;
}
RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC);
RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMULL);
/* Get the PLL2 configuration -----------------------------------------------*/
if((RCC->CR &RCC_CR_PLL2ON) == RCC_CR_PLL2ON)
{
RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_ON;
}
else
{
RCC_OscInitStruct->PLL2.PLL2State = RCC_PLL2_OFF;
}
RCC_OscInitStruct->PLL2.HSEPrediv2Value = __HAL_RCC_HSE_GET_PREDIV2();
RCC_OscInitStruct->PLL2.PLL2MUL = (uint32_t)(RCC->CFGR2 & RCC_CFGR2_PLL2MUL);
}
/**
* @}
*/
#endif /* STM32F105xC || STM32F107xC*/
#if defined (STM32F100xB) || defined (STM32F100xE)
/** @addtogroup RCC_Exported_Functions_Group2
* @{
*/
/**
* @brief Returns the SYSCLK frequency
*
* @note The system frequency computed by this function is not the real
* frequency in the chip. It is calculated based on the predefined
* constant and the selected clock source:
* @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
* @note If SYSCLK source is HSE, function returns values based on HSE_VALUE
* divided by PREDIV factor(**)
* @note If SYSCLK source is PLL, function returns values based on HSE_VALUE
* divided by PREDIV factor(**) or HSI_VALUE(*) multiplied by the PLL factor.
* @note (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value
* 8 MHz).
* @note (**) HSE_VALUE is a constant defined in stm32f1xx_hal_conf.h file (default value
* 8 MHz), user has to ensure that HSE_VALUE is same as the real
* frequency of the crystal used. Otherwise, this function may
* have wrong result.
*
* @note The result of this function could be not correct when using fractional
* value for HSE crystal.
*
* @note This function can be used by the user application to compute the
* baudrate for the communication peripherals or configure other parameters.
*
* @note Each time SYSCLK changes, this function must be called to update the
* right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
*
*
* @retval SYSCLK frequency
*/
uint32_t HAL_RCC_GetSysClockFreq(void)
{
const uint8_t aPLLMULFactorTable[16] = { 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 16};
const uint8_t aPredivFactorTable[16] = { 1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12, 13, 14, 15, 16};
uint32_t tmp_reg = 0, prediv1 = 0, pllclk = 0, pllmul = 0;
uint32_t sysclockfreq = 0;
tmp_reg = RCC->CFGR;
/* Get SYSCLK source -------------------------------------------------------*/
switch (tmp_reg & RCC_CFGR_SWS)
{
case RCC_CFGR_SWS_HSE: /* HSE used as system clock */
{
sysclockfreq = HSE_VALUE;
break;
}
case RCC_CFGR_SWS_PLL: /* PLL used as system clock */
{
pllmul = aPLLMULFactorTable[(uint32_t)(tmp_reg & RCC_CFGR_PLLMULL) >> POSITION_VAL(RCC_CFGR_PLLMULL)];
if ((tmp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2)
{
prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> POSITION_VAL(RCC_CFGR2_PREDIV1)];
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */
pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul);
}
else
{
/* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */
pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul);
}
sysclockfreq = pllclk;
break;
}
case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */
default: /* HSI used as system clock */
{
sysclockfreq = HSI_VALUE;
break;
}
}
return sysclockfreq;
}
/**
* @}
*/
#endif /* STM32F100xB || STM32F100xE*/
#if defined(STM32F101x6) || defined(STM32F101xB) || defined(STM32F101xE) || defined(STM32F101xG) || \
defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || \
defined(STM32F103xE) || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
/** @addtogroup RCC_Exported_Functions_Group2
* @{
*/
/**
* @brief Configures the RCC_ClkInitStruct according to the internal
* RCC configuration registers.
* @param RCC_ClkInitStruct: pointer to an RCC_ClkInitTypeDef structure that
* will be configured.
* @param pFLatency: Pointer on the Flash Latency.
* @retval None
*/
void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency)
{
/* Check the parameters */
assert_param(RCC_ClkInitStruct != NULL);
assert_param(pFLatency != NULL);
/* Set all possible values for the Clock type parameter --------------------*/
RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
/* Get the SYSCLK configuration --------------------------------------------*/
RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW);
/* Get the HCLK configuration ----------------------------------------------*/
RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE);
/* Get the APB1 configuration ----------------------------------------------*/
RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1);
/* Get the APB2 configuration ----------------------------------------------*/
RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3);
/* Get the Flash Wait State (Latency) configuration ------------------------*/
*pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY);
}
/**
* @}
*/
#endif /* STM32F101x6 || STM32F101xB || STM32F101xE || (...) || STM32F105xC || STM32F107xC */
/**
* @}
*/
/**
* @}
*/
/** @addtogroup RCCEx
* @{
*/
/** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions
* @{
*/
/** @defgroup RCCEx_Exported_Functions_Group1 Peripheral Control functions
* @brief Extended Peripheral Control functions
*
@verbatim
===============================================================================
##### Extended Peripheral Control functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to control the RCC Clocks
frequencies.
[..]
(@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to
select the RTC clock source; in this case the Backup domain will be reset in
order to modify the RTC Clock source, as consequence RTC registers (including
the backup registers) and RCC_BDCR register are set to their reset values.
@endverbatim
* @{
*/
/**
* @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the
* RCC_PeriphCLKInitTypeDef.
* @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that
* contains the configuration information for the Extended Peripherals clocks(RTC clock).
*
* @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select
* the RTC clock source; in this case the Backup domain will be reset in
* order to modify the RTC Clock source, as consequence RTC registers (including
* the backup registers) are set to their reset values.
*
* @note In case of STM32F105xC or STM32F107xC devices, PLLI2S will be enabled if requested on
* one of 2 I2S interfaces. When PLLI2S is enabled, you need to call HAL_RCCEx_DisablePLLI2S to
* manually disable it.
*
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit)
{
uint32_t tickstart = 0, tmp_reg = 0;
#if defined(STM32F105xC) || defined(STM32F107xC)
uint32_t pllactive = 0;
#endif /* STM32F105xC || STM32F107xC */
/* Check the parameters */
assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection));
/*------------------------------- RTC/LCD Configuration ------------------------*/
if ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC))
{
/* Enable Power Controller clock */
__HAL_RCC_PWR_CLK_ENABLE();
/* Enable write access to Backup domain */
SET_BIT(PWR->CR, PWR_CR_DBP);
/* Wait for Backup domain Write protection disable */
tickstart = HAL_GetTick();
while((PWR->CR & PWR_CR_DBP) == RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
tmp_reg = (RCC->BDCR & RCC_BDCR_RTCSEL);
/* Reset the Backup domain only if the RTC Clock source selection is modified */
if((tmp_reg != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL)))
{
/* Store the content of BDCR register before the reset of Backup Domain */
tmp_reg = (RCC->BDCR & ~(RCC_BDCR_RTCSEL));
/* RTC Clock selection can be changed only if the Backup Domain is reset */
__HAL_RCC_BACKUPRESET_FORCE();
__HAL_RCC_BACKUPRESET_RELEASE();
/* Restore the Content of BDCR register */
RCC->BDCR = tmp_reg;
}
/* If LSE is selected as RTC clock source, wait for LSE reactivation */
if ((PeriphClkInit->RTCClockSelection == RCC_RTCCLKSOURCE_LSE))
{
/* Get timeout */
tickstart = HAL_GetTick();
/* Wait till LSE is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
__HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection);
}
/*------------------------------ ADC clock Configuration ------------------*/
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC)
{
/* Check the parameters */
assert_param(IS_RCC_ADCPLLCLK_DIV(PeriphClkInit->AdcClockSelection));
/* Configure the ADC clock source */
__HAL_RCC_ADC_CONFIG(PeriphClkInit->AdcClockSelection);
}
#if defined(STM32F105xC) || defined(STM32F107xC)
/*------------------------------ I2S2 Configuration ------------------------*/
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S2) == RCC_PERIPHCLK_I2S2)
{
/* Check the parameters */
assert_param(IS_RCC_I2S2CLKSOURCE(PeriphClkInit->I2s2ClockSelection));
/* Configure the I2S2 clock source */
__HAL_RCC_I2S2_CONFIG(PeriphClkInit->I2s2ClockSelection);
}
/*------------------------------ I2S3 Configuration ------------------------*/
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S3) == RCC_PERIPHCLK_I2S3)
{
/* Check the parameters */
assert_param(IS_RCC_I2S3CLKSOURCE(PeriphClkInit->I2s3ClockSelection));
/* Configure the I2S3 clock source */
__HAL_RCC_I2S3_CONFIG(PeriphClkInit->I2s3ClockSelection);
}
/*------------------------------ PLL I2S Configuration ----------------------*/
/* Check that PLLI2S need to be enabled */
if (HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_I2S2SRC) || HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_I2S3SRC))
{
/* Update flag to indicate that PLL I2S should be active */
pllactive = 1;
}
/* Check if PLL I2S need to be enabled */
if (pllactive == 1)
{
/* Enable PLL I2S only if not active */
if (HAL_IS_BIT_CLR(RCC->CR, RCC_CR_PLL3ON))
{
/* Check the parameters */
assert_param(IS_RCC_PLLI2S_MUL(PeriphClkInit->PLLI2S.PLLI2SMUL));
assert_param(IS_RCC_HSE_PREDIV2(PeriphClkInit->PLLI2S.HSEPrediv2Value));
/* Prediv2 can be written only when the PLL2 is disabled. */
/* Return an error only if new value is different from the programmed value */
if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLL2ON) && \
(__HAL_RCC_HSE_GET_PREDIV2() != PeriphClkInit->PLLI2S.HSEPrediv2Value))
{
return HAL_ERROR;
}
/* Configure the HSE prediv2 factor --------------------------------*/
__HAL_RCC_HSE_PREDIV2_CONFIG(PeriphClkInit->PLLI2S.HSEPrediv2Value);
/* Configure the main PLLI2S multiplication factors. */
__HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SMUL);
/* Enable the main PLLI2S. */
__HAL_RCC_PLLI2S_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLLI2S is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* Return an error only if user wants to change the PLLI2SMUL whereas PLLI2S is active */
if (READ_BIT(RCC->CFGR2, RCC_CFGR2_PLL3MUL) != PeriphClkInit->PLLI2S.PLLI2SMUL)
{
return HAL_ERROR;
}
}
}
#endif /* STM32F105xC || STM32F107xC */
#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
/*------------------------------ USB clock Configuration ------------------*/
if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB)
{
/* Check the parameters */
assert_param(IS_RCC_USBPLLCLK_DIV(PeriphClkInit->UsbClockSelection));
/* Configure the USB clock source */
__HAL_RCC_USB_CONFIG(PeriphClkInit->UsbClockSelection);
}
#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
return HAL_OK;
}
/**
* @brief Get the PeriphClkInit according to the internal
* RCC configuration registers.
* @param PeriphClkInit: pointer to an RCC_PeriphCLKInitTypeDef structure that
* returns the configuration information for the Extended Peripherals clocks(RTC, I2S, ADC clocks).
* @retval None
*/
void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit)
{
uint32_t srcclk = 0;
/* Set all possible values for the extended clock type parameter------------*/
PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_RTC;
/* Get the RTC configuration -----------------------------------------------*/
srcclk = __HAL_RCC_GET_RTC_SOURCE();
/* Source clock is LSE or LSI*/
PeriphClkInit->RTCClockSelection = srcclk;
/* Get the ADC clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_ADC;
PeriphClkInit->AdcClockSelection = __HAL_RCC_GET_ADC_SOURCE();
#if defined(STM32F105xC) || defined(STM32F107xC)
/* Get the I2S2 clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S2;
PeriphClkInit->I2s2ClockSelection = __HAL_RCC_GET_I2S2_SOURCE();
/* Get the I2S3 clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S3;
PeriphClkInit->I2s3ClockSelection = __HAL_RCC_GET_I2S3_SOURCE();
#endif /* STM32F105xC || STM32F107xC */
#if defined(STM32F103xE) || defined(STM32F103xG)
/* Get the I2S2 clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S2;
PeriphClkInit->I2s2ClockSelection = RCC_I2S2CLKSOURCE_SYSCLK;
/* Get the I2S3 clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_I2S3;
PeriphClkInit->I2s3ClockSelection = RCC_I2S3CLKSOURCE_SYSCLK;
#endif /* STM32F103xE || STM32F103xG */
#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
/* Get the USB clock configuration -----------------------------------------*/
PeriphClkInit->PeriphClockSelection |= RCC_PERIPHCLK_USB;
PeriphClkInit->UsbClockSelection = __HAL_RCC_GET_USB_SOURCE();
#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
}
/**
* @brief Returns the peripheral clock frequency
* @note Returns 0 if peripheral clock is unknown
* @param PeriphClk: Peripheral clock identifier
* This parameter can be one of the following values:
* @arg RCC_PERIPHCLK_RTC: RTC peripheral clock
* @arg RCC_PERIPHCLK_ADC: ADC peripheral clock
* @arg RCC_PERIPHCLK_I2S2: I2S2 peripheral clock (STM32F103xE, STM32F103xG, STM32F105xC & STM32F107xC)
* @arg RCC_PERIPHCLK_I2S3: I2S3 peripheral clock (STM32F103xE, STM32F103xG, STM32F105xC & STM32F107xC)
* @arg RCC_PERIPHCLK_USB: USB peripheral clock (STM32F102xx, STM32F103xx, STM32F105xC & STM32F107xC)
* @retval Frequency in Hz (0: means that no available frequency for the peripheral)
*/
uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk)
{
#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
#if defined(STM32F105xC) || defined(STM32F107xC)
const uint8_t aPLLMULFactorTable[12] = {0, 0, 4, 5, 6, 7, 8, 9, 0, 0, 0, 13};
const uint8_t aPredivFactorTable[16] = { 1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12, 13, 14, 15, 16};
#else
const uint8_t aPLLMULFactorTable[16] = { 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 16};
const uint8_t aPredivFactorTable[2] = { 1, 2};
#endif
#endif
uint32_t tmp_reg = 0, frequency = 0;
#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
uint32_t prediv1 = 0, pllclk = 0, pllmul = 0;
#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
#if defined(STM32F105xC) || defined(STM32F107xC)
uint32_t pll2mul = 0, pll3mul = 0, prediv2 = 0;
#endif /* STM32F105xC || STM32F107xC */
/* Check the parameters */
assert_param(IS_RCC_PERIPHCLOCK(PeriphClk));
switch (PeriphClk)
{
#if defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
case RCC_PERIPHCLK_USB:
{
/* Get RCC configuration ------------------------------------------------------*/
tmp_reg = RCC->CFGR;
/* Check if PLL is enabled */
if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLLON))
{
pllmul = aPLLMULFactorTable[(uint32_t)(tmp_reg & RCC_CFGR_PLLMULL) >> POSITION_VAL(RCC_CFGR_PLLMULL)];
if ((tmp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2)
{
#if defined(STM32F105xC) || defined(STM32F107xC) || defined (STM32F100xB) || defined (STM32F100xE)
prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV1) >> POSITION_VAL(RCC_CFGR2_PREDIV1)];
#else
prediv1 = aPredivFactorTable[(uint32_t)(RCC->CFGR & RCC_CFGR_PLLXTPRE) >> POSITION_VAL(RCC_CFGR_PLLXTPRE)];
#endif /* STM32F105xC || STM32F107xC || STM32F100xB || STM32F100xE */
#if defined(STM32F105xC) || defined(STM32F107xC)
if(HAL_IS_BIT_SET(RCC->CFGR2, RCC_CFGR2_PREDIV1SRC))
{
/* PLL2 selected as Prediv1 source */
/* PLLCLK = PLL2CLK / PREDIV1 * PLLMUL with PLL2CLK = HSE/PREDIV2 * PLL2MUL */
prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> POSITION_VAL(RCC_CFGR2_PREDIV2)) + 1;
pll2mul = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> POSITION_VAL(RCC_CFGR2_PLL2MUL)) + 2;
pllclk = (uint32_t)((((HSE_VALUE / prediv2) * pll2mul) / prediv1) * pllmul);
}
else
{
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */
pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul);
}
/* If PLLMUL was set to 13 means that it was to cover the case PLLMUL 6.5 (avoid using float) */
/* In this case need to divide pllclk by 2 */
if (pllmul == aPLLMULFactorTable[(uint32_t)(RCC_CFGR_PLLMULL6_5) >> POSITION_VAL(RCC_CFGR_PLLMULL)])
{
pllclk = pllclk / 2;
}
#else
if ((tmp_reg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI_DIV2)
{
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV1 * PLLMUL */
pllclk = (uint32_t)((HSE_VALUE / prediv1) * pllmul);
}
#endif /* STM32F105xC || STM32F107xC */
}
else
{
/* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */
pllclk = (uint32_t)((HSI_VALUE >> 1) * pllmul);
}
/* Calcul of the USB frequency*/
#if defined(STM32F105xC) || defined(STM32F107xC)
/* USBCLK = PLLVCO = (2 x PLLCLK) / USB prescaler */
if (__HAL_RCC_GET_USB_SOURCE() == RCC_USBPLLCLK_DIV2)
{
/* Prescaler of 2 selected for USB */
frequency = pllclk;
}
else
{
/* Prescaler of 3 selected for USB */
frequency = (2 * pllclk) / 3;
}
#else
/* USBCLK = PLLCLK / USB prescaler */
if (__HAL_RCC_GET_USB_SOURCE() == RCC_USBPLLCLK_DIV1)
{
/* No prescaler selected for USB */
frequency = pllclk;
}
else
{
/* Prescaler of 1.5 selected for USB */
frequency = (pllclk * 2) / 3;
}
#endif
}
break;
}
#endif /* STM32F102x6 || STM32F102xB || STM32F103x6 || STM32F103xB || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
#if defined (STM32F103xE) || defined (STM32F103xG) || defined (STM32F105xC) || defined (STM32F107xC)
case RCC_PERIPHCLK_I2S2:
{
#if defined (STM32F103xE) || defined (STM32F103xG)
/* SYSCLK used as source clock for I2S2 */
frequency = HAL_RCC_GetSysClockFreq();
#else
if (__HAL_RCC_GET_I2S2_SOURCE() == RCC_I2S2CLKSOURCE_SYSCLK)
{
/* SYSCLK used as source clock for I2S2 */
frequency = HAL_RCC_GetSysClockFreq();
}
else
{
/* Check if PLLI2S is enabled */
if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON))
{
/* PLLI2SVCO = 2 * PLLI2SCLK = 2 * (HSE/PREDIV2 * PLL3MUL) */
prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> POSITION_VAL(RCC_CFGR2_PREDIV2)) + 1;
pll3mul = ((RCC->CFGR2 & RCC_CFGR2_PLL3MUL) >> POSITION_VAL(RCC_CFGR2_PLL3MUL)) + 2;
frequency = (uint32_t)(2 * ((HSE_VALUE / prediv2) * pll3mul));
}
}
#endif /* STM32F103xE || STM32F103xG */
break;
}
case RCC_PERIPHCLK_I2S3:
{
#if defined (STM32F103xE) || defined (STM32F103xG)
/* SYSCLK used as source clock for I2S3 */
frequency = HAL_RCC_GetSysClockFreq();
#else
if (__HAL_RCC_GET_I2S3_SOURCE() == RCC_I2S3CLKSOURCE_SYSCLK)
{
/* SYSCLK used as source clock for I2S3 */
frequency = HAL_RCC_GetSysClockFreq();
}
else
{
/* Check if PLLI2S is enabled */
if (HAL_IS_BIT_SET(RCC->CR, RCC_CR_PLL3ON))
{
/* PLLI2SVCO = 2 * PLLI2SCLK = 2 * (HSE/PREDIV2 * PLL3MUL) */
prediv2 = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> POSITION_VAL(RCC_CFGR2_PREDIV2)) + 1;
pll3mul = ((RCC->CFGR2 & RCC_CFGR2_PLL3MUL) >> POSITION_VAL(RCC_CFGR2_PLL3MUL)) + 2;
frequency = (uint32_t)(2 * ((HSE_VALUE / prediv2) * pll3mul));
}
}
#endif /* STM32F103xE || STM32F103xG */
break;
}
#endif /* STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
case RCC_PERIPHCLK_RTC:
{
/* Get RCC BDCR configuration ------------------------------------------------------*/
tmp_reg = RCC->BDCR;
/* Check if LSE is ready if RTC clock selection is LSE */
if (((tmp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_LSE) && (HAL_IS_BIT_SET(tmp_reg, RCC_BDCR_LSERDY)))
{
frequency = LSE_VALUE;
}
/* Check if LSI is ready if RTC clock selection is LSI */
else if (((tmp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_LSI) && (HAL_IS_BIT_SET(RCC->CSR, RCC_CSR_LSIRDY)))
{
frequency = LSI_VALUE;
}
else if (((tmp_reg & RCC_BDCR_RTCSEL) == RCC_RTCCLKSOURCE_HSE_DIV128) && (HAL_IS_BIT_SET(RCC->CR, RCC_CR_HSERDY)))
{
frequency = HSE_VALUE / 128;
}
/* Clock not enabled for RTC*/
else
{
frequency = 0;
}
break;
}
case RCC_PERIPHCLK_ADC:
{
frequency = HAL_RCC_GetPCLK2Freq() / (((__HAL_RCC_GET_ADC_SOURCE() >> POSITION_VAL(RCC_CFGR_ADCPRE_DIV4)) + 1) * 2);
break;
}
default:
{
break;
}
}
return(frequency);
}
/**
* @}
*/
#if defined(STM32F105xC) || defined(STM32F107xC)
/** @defgroup RCCEx_Exported_Functions_Group2 PLLI2S Management function
* @brief PLLI2S Management functions
*
@verbatim
===============================================================================
##### Extended PLLI2S Management functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to control the PLLI2S
activation or deactivation
@endverbatim
* @{
*/
/**
* @brief Enable PLLI2S
* @param PLLI2SInit: pointer to an RCC_PLLI2SInitTypeDef structure that
* contains the configuration information for the PLLI2S
* @note The PLLI2S configuration not modified if used by I2S2 or I2S3 Interface.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCCEx_EnablePLLI2S(RCC_PLLI2SInitTypeDef *PLLI2SInit)
{
uint32_t tickstart = 0;
/* Check that PLL I2S has not been already enabled by I2S2 or I2S3*/
if (HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S2SRC) && HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S3SRC))
{
/* Check the parameters */
assert_param(IS_RCC_PLLI2S_MUL(PLLI2SInit->PLLI2SMUL));
assert_param(IS_RCC_HSE_PREDIV2(PLLI2SInit->HSEPrediv2Value));
/* Prediv2 can be written only when the PLL2 is disabled. */
/* Return an error only if new value is different from the programmed value */
if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLL2ON) && \
(__HAL_RCC_HSE_GET_PREDIV2() != PLLI2SInit->HSEPrediv2Value))
{
return HAL_ERROR;
}
/* Disable the main PLLI2S. */
__HAL_RCC_PLLI2S_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLLI2S is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Configure the HSE prediv2 factor --------------------------------*/
__HAL_RCC_HSE_PREDIV2_CONFIG(PLLI2SInit->HSEPrediv2Value);
/* Configure the main PLLI2S multiplication factors. */
__HAL_RCC_PLLI2S_CONFIG(PLLI2SInit->PLLI2SMUL);
/* Enable the main PLLI2S. */
__HAL_RCC_PLLI2S_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLLI2S is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* PLLI2S cannot be modified as already used by I2S2 or I2S3 */
return HAL_ERROR;
}
return HAL_OK;
}
/**
* @brief Disable PLLI2S
* @note PLLI2S is not disabled if used by I2S2 or I2S3 Interface.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCCEx_DisablePLLI2S(void)
{
uint32_t tickstart = 0;
/* Disable PLL I2S as not requested by I2S2 or I2S3*/
if (HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S2SRC) && HAL_IS_BIT_CLR(RCC->CFGR2, RCC_CFGR2_I2S3SRC))
{
/* Disable the main PLLI2S. */
__HAL_RCC_PLLI2S_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLLI2S is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
else
{
/* PLLI2S is currently used by I2S2 or I2S3. Cannot be disabled.*/
return HAL_ERROR;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup RCCEx_Exported_Functions_Group3 PLL2 Management function
* @brief PLL2 Management functions
*
@verbatim
===============================================================================
##### Extended PLL2 Management functions #####
===============================================================================
[..]
This subsection provides a set of functions allowing to control the PLL2
activation or deactivation
@endverbatim
* @{
*/
/**
* @brief Enable PLL2
* @param PLL2Init: pointer to an RCC_PLL2InitTypeDef structure that
* contains the configuration information for the PLL2
* @note The PLL2 configuration not modified if used indirectly as system clock.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCCEx_EnablePLL2(RCC_PLL2InitTypeDef *PLL2Init)
{
uint32_t tickstart = 0;
/* This bit can not be cleared if the PLL2 clock is used indirectly as system
clock (i.e. it is used as PLL clock entry that is used as system clock). */
if((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \
(__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \
((READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2))
{
return HAL_ERROR;
}
else
{
/* Check the parameters */
assert_param(IS_RCC_PLL2_MUL(PLL2Init->PLL2MUL));
assert_param(IS_RCC_HSE_PREDIV2(PLL2Init->HSEPrediv2Value));
/* Prediv2 can be written only when the PLLI2S is disabled. */
/* Return an error only if new value is different from the programmed value */
if (HAL_IS_BIT_SET(RCC->CR,RCC_CR_PLL3ON) && \
(__HAL_RCC_HSE_GET_PREDIV2() != PLL2Init->HSEPrediv2Value))
{
return HAL_ERROR;
}
/* Disable the main PLL2. */
__HAL_RCC_PLL2_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
/* Configure the HSE prediv2 factor --------------------------------*/
__HAL_RCC_HSE_PREDIV2_CONFIG(PLL2Init->HSEPrediv2Value);
/* Configure the main PLL2 multiplication factors. */
__HAL_RCC_PLL2_CONFIG(PLL2Init->PLL2MUL);
/* Enable the main PLL2. */
__HAL_RCC_PLL2_ENABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is ready */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) == RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
return HAL_OK;
}
/**
* @brief Disable PLL2
* @note PLL2 is not disabled if used indirectly as system clock.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RCCEx_DisablePLL2(void)
{
uint32_t tickstart = 0;
/* This bit can not be cleared if the PLL2 clock is used indirectly as system
clock (i.e. it is used as PLL clock entry that is used as system clock). */
if((__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE) && \
(__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && \
((READ_BIT(RCC->CFGR2,RCC_CFGR2_PREDIV1SRC)) == RCC_CFGR2_PREDIV1SRC_PLL2))
{
return HAL_ERROR;
}
else
{
/* Disable the main PLL2. */
__HAL_RCC_PLL2_DISABLE();
/* Get Start Tick*/
tickstart = HAL_GetTick();
/* Wait till PLL2 is disabled */
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLL2RDY) != RESET)
{
if((HAL_GetTick() - tickstart ) > PLL2_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
}
return HAL_OK;
}
/**
* @}
*/
#endif /* STM32F105xC || STM32F107xC */
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_RCC_MODULE_ENABLED */
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/