# Target file name (without extension).
-TARGET = adb_usb
+TARGET ?= adb_usb
# Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
-# keyboard dependent files
-SRC = keymap.c \
- matrix.c \
- led.c \
+# project specific files
+SRC ?= matrix.c \
adb.c
CONFIG_H = config.h
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162 # Teensy 1.0
-MCU = atmega32u4 # Teensy 2.0
-#MCU = at90usb646 # Teensy++ 1.0
-#MCU = at90usb1286 # Teensy++ 2.0
-
+# MCU name
+# atmega32u4 Teensy2.0
+# atemga32u4 TMK Converter rev.1
+# atemga32u2 TMK Converter rev.2
+MCU ?= atmega32u2
# Processor frequency.
-# Normally the first thing your program should do is set the clock prescaler,
-# so your program will run at the correct speed. You should also set this
-# variable to same clock speed. The _delay_ms() macro uses this, and many
-# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU ?= 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
+# LUFA bootloader 4096
+# USBaspLoader 2048
+BOOTLOADER_SIZE ?= 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
# Build Options
# comment out to disable the options.
#
-#MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes # Audio control and System control
-#NKRO_ENABLE = yes # USB Nkey Rollover
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+NKRO_ENABLE ?= no # USB Nkey Rollover
+ADB_MOUSE_ENABLE ?= yes # ADB Mouse support
+UNIMAP_ENABLE ?= yes # Use unimap
+ACTIONMAP_ENABLE ?= no # Use 16bit actionmap instead of 8bit keymap
+KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor
+
+# ADB Mice need acceleration for todays much bigger screens.
+ADB_MOUSE_MAXACC ?= 8
+OPT_DEFS += -DADB_MOUSE_MAXACC=$(ADB_MOUSE_MAXACC)
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+
+#
+# Keymap file
+#
+ifeq (yes,$(strip $(UNIMAP_ENABLE)))
+ KEYMAP_FILE = unimap
+else
+ ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
+ KEYMAP_FILE = actionmap
+ else
+ KEYMAP_FILE = keymap
+ endif
+endif
+ifdef KEYMAP
+ SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+ SRC := $(KEYMAP_FILE)_plain.c $(SRC)
+endif
# Search Path
VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk