-#
-# Makefile for PJRC Teensy
-#
-
-
# Target file name (without extension).
-TARGET = ps2_usb_pjrc
+TARGET ?= ps2_usb
# Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
-# keyboard dependent files
-SRC = main.c \
- keymap.c \
- matrix.c \
- led.c \
- ps2.c
+# project specific files
+SRC ?= matrix.c \
+ led.c
-CONFIG_H = config_pjrc.h
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+ KEYMAP_FILE = unimap
+else
+ ifdef ACTIONMAP_ENABLE
+ KEYMAP_FILE = actionmap
+ else
+ KEYMAP_FILE = keymap
+ endif
+endif
+ifdef KEYMAP
+ SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+ SRC := $(KEYMAP_FILE)_plain.c $(SRC)
+endif
+
+CONFIG_H ?= config.h
+
+
+# MCU name
+MCU ?= atmega32u2
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU ?= 16000000
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162 # Teensy 1.0
-MCU = atmega32u4 # Teensy 2.0
-#MCU = at90usb646 # Teensy++ 1.0
-#MCU = at90usb1286 # Teensy++ 2.0
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
-# Processor frequency.
-# Normally the first thing your program should do is set the clock prescaler,
-# so your program will run at the correct speed. You should also set this
-# variable to same clock speed. The _delay_ms() macro uses this, and many
-# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
+
+# This improves response of keyboard when wakeup
+OPT_DEFS += -DSUSPEND_MODE_STANDBY
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+BOOTLOADER_SIZE ?= 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
# Build Options
-# *Comment out* to disable the options.
+# comment out to disable the options.
#
-MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes # Audio control and System control
-NKRO_ENABLE = yes # USB Nkey Rollover
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+NKRO_ENABLE ?= yes # USB Nkey Rollover
+# PS/2 Options
+#
+#PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened)
+PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT ?= yes # uses primitive reference code
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk