ibmpc_usb: Update prebuilt firmware hex files

[max/tmk_keyboard.git] / converter / m0110_usb / Makefile

diff --git a/converter/m0110_usb/Makefile b/converter/m0110_usb/Makefile
index bf0f083f6d4e48f266c1ffa40e17465cb08a3fd8..71d675ac7f43b6f67814c1f962ddca8a03f29f4d 100644 (file)
--- a/converter/m0110_usb/Makefile
+++ b/converter/m0110_usb/Makefile
@@ -1,27 +1,41 @@
 # Target file name (without extension).
-TARGET = m0110
+TARGET ?= m0110_usb
 
 # Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
 # keyboard dependent files
-SRC =  keymap.c \
-       matrix.c \
+SRC ?= matrix.c \
        led.c \
        m0110.c
 
-CONFIG_H = config.h
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+    KEYMAP_FILE = unimap
+else
+    ifdef ACTIONMAP_ENABLE
+       KEYMAP_FILE = actionmap
+    else
+       KEYMAP_FILE = keymap
+    endif
+endif
+ifdef KEYMAP
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+    SRC := $(KEYMAP_FILE).c $(SRC)
+endif
+
+CONFIG_H ?= config.h
 
 
 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
+MCU ?= atmega32u2
 
 
 # Processor frequency.
@@ -29,29 +43,63 @@ MCU = atmega32u4       # Teensy 2.0
 #   so your program will run at the correct speed.  You should also set this
 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
 #   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
+F_CPU ?= 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
 
 
 # Build Options
 #   *Comment out* to disable the options.
 #
-#MOUSEKEY_ENABLE = yes # Mouse keys
-#PS2_MOUSE_ENABLE = yes        # PS/2 mouse(TrackPoint) support
-#EXTRAKEY_ENABLE = yes # Audio control and System control
-#NKRO_ENABLE = yes     # USB Nkey Rollover
+#BOOTMAGIC_ENABLE ?= yes       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes  # Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE ?= yes    # USB Nkey Rollover
+#KEYMAP_SECTION_ENABLE ?= yes  # fixed address keymap for keymap editor
 
 
 
 #---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+PROGRAM_CMD ?= teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
 
 
 # Search Path
 VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
 
 
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk