# Target file name (without extension).
-TARGET = m0110_lufa
+TARGET ?= m0110_usb
# Directory common source filess exist
-TMK_DIR = ../../tmk_core
+TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
# keyboard dependent files
-SRC = matrix.c \
+SRC ?= matrix.c \
led.c \
m0110.c
-# To use own keymap file run make like: make keymap=hasu
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+ KEYMAP_FILE = unimap
+else
+ ifdef ACTIONMAP_ENABLE
+ KEYMAP_FILE = actionmap
+ else
+ KEYMAP_FILE = keymap
+ endif
+endif
ifdef KEYMAP
- SRC += keymap_$(KEYMAP).c
+ SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
else
- SRC += keymap_default.c
+ SRC := $(KEYMAP_FILE).c $(SRC)
endif
-CONFIG_H = config.h
+CONFIG_H ?= config.h
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
-MCU = atmega32u2 # TMK converter rev2
-#MCU = atmega32u4 # TMK converter rev1
+MCU ?= atmega32u2
# Processor frequency.
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
+F_CPU ?= 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
+ARCH ?= AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
+F_USB ?= $(F_CPU)
# Interrupt driven control endpoint task
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options
# *Comment out* to disable the options.
#
-#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
+#BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+#SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
+#NKRO_ENABLE ?= yes # USB Nkey Rollover
+#KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor
#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+PROGRAM_CMD ?= teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
# Search Path