M0110/M0110A to USB keyboard converter
======================================
-This firmware converts the protocol of Apple Macintosh keyboard M0110/M0110A into USB.
-Target board of this project is [PJRC Teensy](http://www.pjrc.com/teensy/), though,
-you can use other board with USB AVR like `ATmega32U4` and `AT90USB`.
+This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller like **ATmega32U2** and **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
-![M0110](https://github.com/tmk/tmk_keyboard/raw/master/m0110_usb/doc/m0110.jpg)
+Read README of top directory too.
-M0110A support was contributed by [skagon@github](https://github.com/skagon).
+Pictures of **M0110 + M0120** and **M0110A** with [TMK converter].
+![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)
+![M0110A](http://i.imgur.com/HuHOEoHm.jpg)
-Connection
-----------
-You need 4P4C plug and cable to connect Teensy or other AVR dev board into the keyboard.
-Teensy port `PF0` is assigned for `CLOCK` line and `PF1` for `DATA` by default,
-you can change pin configuration with editing *config.h*.
+- M0110A support was contributed by [skagon@github](https://github.com/skagon).
+- M0120 also is supported. keys(+ * / and ,) on M0120 are recognized as cursor keys.
-You can find 4P4C plugs on telephone handset cable. Note that it is *crossover* connection
-while Macintosh keyboard cable is *straight*.
-[![Conection](http://i.imgur.com/vJoVOm.jpg)](http://i.imgur.com/vJoVO.jpg)
-In this pic:
+Update
+------
+- 2013/08: Change port for signals `PF` to `PD`
+- 2013/09: Change port again, it uses inversely `PD0` for data and `PD1` for clock line now.
+- 2014/06: Change keymaps
+- 2015/03: Add support for "International"(ISO) keyboard(keymap_intl.c)
+- 2016/09: Unimap support - keymap editor on web browser
+
+
+
+Hardware
+--------
+You can buy preassembled [TMK converter] or make yourown with AVR dev board like PJRC [Teensy].
-1. `GND`(Black)
-2. `CLOCK`(Red)
-3. `DATA`(Green)
-4. `+5V`(Yellow)
+Port of the MCU `PD1` is assigned to `CLOCK` line and `PD0` to `DATA` by default, you can change pin configuration with editing `config.h`.
-Not that wire colors may vary in your cable.
+[![M0110 Converter](http://i.imgur.com/yEp2eRim.jpg)](http://i.imgur.com/yEp2eRi.jpg)
+### 4P4C phone handset cable
+Note that original cable used with Mac is **straight** while phone handset cable is **crossover**.
-### Pinout
+<http://en.wikipedia.org/wiki/Modular_connector#4P4C>
+
+[Teensy]: http://www.pjrc.com/teensy/
+[TMK converter]: https://geekhack.org/index.php?topic=72052.0
+
+
+### Socket Pinout
- <http://pinouts.ru/Inputs/MacKeyboard_pinout.shtml>
-- <http://en.wikipedia.org/wiki/Modular_connector#4P4C>
![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
-### Pull-up Registor
-You may need pull-up registors on signal lines(`CLOCK`, `DATA`) in particular
-when you have long or coiled cable. 1k-10k Ohm will be OK for this purpose.
-In some cases MCU can't read signal from keyboard correctly without pull-up resistors.
+### Pull-up Resistor
+You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
-Building Frimware
+Building Firmware
-----------------
-To compile firmware you need AVR GCC. You can use [WinAVR](http://winavr.sourceforge.net/) on Windows.
-You can edit *Makefile* and *config.h* to change compile options and pin configuration.
+To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration. Also `KEYMAP` option can be used to select keymap.
$ git clone git://github.com/tmk/tmk_keyboard.git (or download source)
$ cd m0110_usb
- $ make
+ $ make -f Makefile.rev2 clean
+ $ make -f Makefile.rev2 [KEYMAP={intl|spacefn}]
-and program your Teensy with [PJRC Teensy loader](http://www.pjrc.com/teensy/loader.html).
+Use `Maefile.rev1` for TMK converter rev.1 and Teensy(ATMega32u4), instead.
Keymap
------
-You can change keymaps by editing *keymap.c*.
-
-### M0110
-#### *Default*
- ,---------------------------------------------------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs|
- |---------------------------------------------------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
- |---------------------------------------------------------|
- |Fn0 | A| S| D| F| G| H| J| K| L| ;| '|Return|
- |---------------------------------------------------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift |
- `---------------------------------------------------------'
- |Ctr|Alt | Space |Gui |Ctr|
- `-----------------------------------------------'
-#### *HHKB/WASD Layer*
- ,---------------------------------------------------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet|
- |---------------------------------------------------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up | |Ins|
- |---------------------------------------------------------|
- |Fn0 |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Return|
- |---------------------------------------------------------|
- |Shift |End| |PgD| |VoD|VoU|Mut|End|PgD|Dow|Shift |
- `---------------------------------------------------------'
- |Ctr|Alt | Space |Gui |Ctr|
- `-----------------------------------------------'
-
-### M0110A
-#### *Default*
- ,---------------------------------------------------------. ,---------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Gui| =| /| *|
- |---------------------------------------------------------| |---------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
- |-----------------------------------------------------' | |---------------|
- |Fn0 | A| S| D| F| G| H| J| K| L| ;| '|Return| | 4| 5| 6| +|
- |---------------------------------------------------------| |---------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft|Up | | 1| 2| 3| |
- |---------------------------------------------------------| |-----------|Ent|
- |Ctrl |Alt | Space | \|Lft|Rgt|Dn | | 0| .| |
- `---------------------------------------------------------' `---------------'
-#### *HHKB/WASD/mousekey Layer*
- ,---------------------------------------------------------. ,---------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk|Mb1|Mb3|Mb2|
- |---------------------------------------------------------| |---------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up | | | |MwD|McU|MwU|MwU|
- |-----------------------------------------------------' | |---------------|
- |Fn0 |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Return| |McL|McD|McR|MwD|
- |---------------------------------------------------------| |---------------|
- |Shift |End| |PgD| |VoD|VoU|Mut|End|PgD|Dow|Shif|Up | |MwL|McD|MwR| |
- |---------------------------------------------------------| |-----------|Mb2|
- |Ctrl |Alt | Space |Ins|Lft|Rgt|Dn | | Mb1|Mb3| |
- `---------------------------------------------------------' `---------------'
+To create your own keymap copy existent keymap file to `keymap_<name>.c` and edit it. You can build with `make -f Makefile.rev2 KEYMAP=<name>`.
+
+Or you can edit keymap on web browser and download firmware.
+http://www.tmk-kbd.com/tmk_keyboard/editor/
Debug
-----
-You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output.
+You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output. The converter has some functions for debug, press `<Magic>+H` simultaneously to get help.
-The converter has some functions for debug, press `Alt+Gui+H` simultaneously to get help.
-These function is totally undocumented, tentative, inconsistent and buggy.
+- Magic combo: `Shift+Option+⌘` or `Shift+Option+Ctrl`(`Shift+Alt+Gui` or `Shift+Alt+Control`)