*/
-#define VENDOR_ID 0xBCBC
+#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0xBCBC
#define DEVICE_VER 0x0500
#define MANUFACTURER t.m.k.
#define MATRIX_ROWS 12 // keycode bit: 3-0
#define MATRIX_COLS 8 // keycode bit: 6-4
-//#define DEBUG_ON_INIT 1
+#define DEBUG_ON_INIT 1
//#define TEENSY_CONFIG 1
-#define PRO_MICRO_CONFIG 1
+//#define PRO_MICRO_CONFIG 1
+#define TMK_CONFIG 1
-// comment out if you don't want the keyboard's LEDs to flash upon initialization
-#define NEXT_KBD_INIT_FLASH_LEDS
+// comment out if you don't want the keyboard's LEDs to flash upon initialization or pressing shift
+//#define NEXT_KBD_INIT_FLASH_LEDS
+//#define NEXT_KBD_SHIFT_FLASH_LEDS
//============= Start of Arduino Pro Micro Configuration ==============
#ifdef PRO_MICRO_CONFIG
#endif
//================= End of Teensy 2.0 Configuration ==================
+
+//================ Start of TMK converter Configuration =================
+#ifdef TMK_CONFIG
+
+// this is the debugging LED that flashes when a key is being pressed
+// comment out in order to disable debugging LED
+#define NEXT_KBD_LED1_PORT PORTD
+#define NEXT_KBD_LED1_PIN PIND
+#define NEXT_KBD_LED1_DDR DDRD
+#define NEXT_KBD_LED1_BIT 6
+
+#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT);
+#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT);
+
+// corresponds to the Keyboard In wire on the NeXT connector
+#define NEXT_KBD_OUT_PORT PORTD
+#define NEXT_KBD_OUT_PIN PIND
+#define NEXT_KBD_OUT_DDR DDRD
+#define NEXT_KBD_OUT_BIT 1
+
+// corresponds to the Keyboard Out wire on the NeXT connector
+#define NEXT_KBD_IN_PORT PORTD
+#define NEXT_KBD_IN_PIN PIND
+#define NEXT_KBD_IN_DDR DDRD
+#define NEXT_KBD_IN_BIT 0
+
+// this pin is an input for the power key on the NeXT keyboard
+// as the keyboard is powered on this should be normally high;
+// if it is pulled low it means the power button is being preseed
+#define NEXT_KBD_PWR_PORT PORTD
+#define NEXT_KBD_PWR_PIN PIND
+#define NEXT_KBD_PWR_DDR DDRD
+#define NEXT_KBD_PWR_BIT 4
+
+#endif
+//================= End of TMK converter Configuration ==================
+
/* key combination for command */
#define IS_COMMAND() ( \
- (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))|| \
- (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL))) \
+ (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) || \
+ (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RALT))) || \
+ (keyboard_report->mods == (MOD_BIT(KC_RGUI) | MOD_BIT(KC_RGUI))) \
)