lufa: Fix comment on INTERRUPT_CONTROL_ENDPOINT

[max/tmk_keyboard.git] / converter / ps2_usb / Makefile

diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile
index 04bf28a00c5c995c020654a9ce3d71502089fd73..5f9c4042c8cd5ae5dc5a88cb84a7ff34f389bcea 100644 (file)
--- a/converter/ps2_usb/Makefile
+++ b/converter/ps2_usb/Makefile
@@ -1,29 +1,39 @@
 # Target file name (without extension).
-TARGET = ps2_usb_lufa
+TARGET ?= ps2_usb
 
 # Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
 # project specific files
-SRC =  keymap_common.c \
-       matrix.c \
+SRC ?= matrix.c \
        led.c
 
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+    KEYMAP_FILE = unimap
+else
+    ifdef ACTIONMAP_ENABLE
+       KEYMAP_FILE = actionmap
+    else
+       KEYMAP_FILE = keymap
+    endif
+endif
 ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
 else
-    SRC := keymap_plain.c $(SRC)
+    SRC := $(KEYMAP_FILE)_plain.c $(SRC)
 endif
 
-CONFIG_H = config.h
+CONFIG_H ?= config.h
 
 
 # MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
+MCU ?= atmega32u2
 
 # Processor frequency.
 #     This will define a symbol, F_CPU, in all source code files equal to the
@@ -36,14 +46,14 @@ MCU = atmega32u4
 #     does not *change* the processor frequency - it should merely be updated to
 #     reflect the processor speed set externally so that the code can use accurate
 #     software delays.
-F_CPU = 16000000
+F_CPU ?= 16000000
 
 
 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
+ARCH ?= AVR8
 
 # Input clock frequency.
 #     This will define a symbol, F_USB, in all source code files equal to the
@@ -56,11 +66,14 @@ ARCH = AVR8
 #
 #     If no clock division is performed on the input clock inside the AVR (via the
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
+F_USB ?= $(F_CPU)
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+# Interrupt driven control endpoint task
+# Not work with suart debug
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
+# This improves response of keyboard when wakeup
+OPT_DEFS += -DSUSPEND_MODE_STANDBY
 
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
@@ -68,25 +81,26 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 #   Atmel DFU loader 4096
 #   LUFA bootloader  4096
 #   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+BOOTLOADER_SIZE ?= 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
 
 
 # Build Options
 #   comment out to disable the options.
 #
-#BOOTMAGIC_ENABLE = yes        # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
-CONSOLE_ENABLE = yes   # Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no  # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes  # Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes     # USB Nkey Rollover
 
 
 # PS/2 Options
 #
-#PS2_USE_USART = yes   # uses hardware USART engine for PS/2 signal receive(recomened)
-#PS2_USE_INT = yes     # uses external interrupt for falling edge of PS/2 clock pin
-PS2_USE_BUSYWAIT = yes # uses primitive reference code
+#PS2_USE_USART ?= yes  # uses hardware USART engine for PS/2 signal receive(recomened)
+PS2_USE_INT ?= yes     # uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT ?= yes       # uses primitive reference code
 
 
 # Optimize size but this may cause error "relocation truncated to fit"
@@ -94,9 +108,9 @@ PS2_USE_BUSYWAIT = yes       # uses primitive reference code
 
 # Search Path
 VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
 
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/protocol/lufa.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk