-#
-# Makefile for PJRC Teensy
-#
-
-
# Target file name (without extension).
-TARGET = x68k_usb_pjrc
+TARGET ?= x68k_usb
# Directory common source filess exist
-TMK_DIR = ../..
+TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
-# keyboard dependent files
-SRC = keymap.c \
- matrix.c \
+# project specific files
+SRC ?= matrix.c \
led.c \
protocol/serial_uart.c
-CONFIG_H = config_pjrc.h
-
+CONFIG_H = config.h
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162 # Teensy 1.0
-MCU = atmega32u4 # Teensy 2.0
-#MCU = at90usb646 # Teensy++ 1.0
-#MCU = at90usb1286 # Teensy++ 2.0
+# MCU name
+# atmega32u4 Teensy2.0
+# atemga32u4 TMK Converter rev.1
+# atemga32u2 TMK Converter rev.2
+MCU ?= atmega32u2
# Processor frequency.
-# Normally the first thing your program should do is set the clock prescaler,
-# so your program will run at the correct speed. You should also set this
-# variable to same clock speed. The _delay_ms() macro uses this, and many
-# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU ?= 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-# Boot Section Size in bytes
+
+# Boot Section Size in *bytes*
# Teensy halfKay 512
-# Atmel DFU loader 4096
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
# LUFA bootloader 4096
+# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
-# *Comment out* to disable the options.
+# comment out to disable the options.
#
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-
-
-
-#---------------- Programming Options --------------------------
-AVRDUDE = avrdude
-# Type: avrdude -c ? to get a full listing.
-AVRDUDE_PROGRAMMER = avr109
-AVRDUDE_PORT = /dev/ttyACM0
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
+#UNIMAP_ENABLE = yes
+#ACTIONMAP_ENABLE = yes # Use 16bit actionmap instead of 8bit keymap
+#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-# Increase verbosity level. Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
+#
+# Keymap file
+#
+ifeq (yes,$(strip $(UNIMAP_ENABLE)))
+ KEYMAP_FILE = unimap
+else
+ ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
+ KEYMAP_FILE = actionmap
+ else
+ KEYMAP_FILE = keymap
+ endif
+endif
+ifdef KEYMAP
+ SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+ SRC := $(KEYMAP_FILE).c $(SRC)
+endif
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol/pjrc.mk
+include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/protocol.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk