alps64: Update firmware binary

[max/tmk_keyboard.git] / keyboard / alps64 / Makefile

diff --git a/keyboard/alps64/Makefile b/keyboard/alps64/Makefile
index 3e0dccc9e9814a2ea9b0595238a3d0960ac6ac33..d9968f7c7995d862ff778c322fde42d671ae08b4 100644 (file)
--- a/keyboard/alps64/Makefile
+++ b/keyboard/alps64/Makefile
@@ -1,68 +1,21 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
 # Target file name (without extension).
-TARGET = alps64
+TARGET ?= alps64
 
 # Directory common source filess exist
-TMK_DIR = ../..
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
 # project specific files
-SRC =  keymap_common.c \
-       matrix.c \
+SRC ?= matrix.c \
        led.c
 
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config.h
+CONFIG_H ?= config.h
 
 
 # MCU name
-MCU = atmega32u2
+MCU ?= atmega32u2
 
 # Processor frequency.
 #     This will define a symbol, F_CPU, in all source code files equal to the
@@ -75,14 +28,14 @@ MCU = atmega32u2
 #     does not *change* the processor frequency - it should merely be updated to
 #     reflect the processor speed set externally so that the code can use accurate
 #     software delays.
-F_CPU = 16000000
+F_CPU ?= 16000000
 
 
 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
+ARCH ?= AVR8
 
 # Input clock frequency.
 #     This will define a symbol, F_USB, in all source code files equal to the
@@ -95,7 +48,7 @@ ARCH = AVR8
 #
 #     If no clock division is performed on the input clock inside the AVR (via the
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
+F_USB ?= $(F_CPU)
 
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
@@ -107,19 +60,40 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 #   Atmel DFU loader 4096
 #   LUFA bootloader  4096
 #   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+BOOTLOADER_SIZE ?= 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
 
 
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
-CONSOLE_ENABLE = yes   # Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes     # USB Nkey Rollover - not yet supported in LUFA
+BOOTMAGIC_ENABLE ?= yes        # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes  # Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE ?= yes    # USB Nkey Rollover
+#ACTIONMAP_ENABLE ?= yes       # Use 16bit action codes in keymap instead of 8bit keycodes
+
+
+#
+# Keymap file
+#
+ifeq (yes,$(strip $(UNIMAP_ENABLE)))
+    KEYMAP_FILE = unimap
+else
+    ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
+        KEYMAP_FILE = actionmap
+    else
+        KEYMAP_FILE = keymap
+    endif
+endif
+ifdef KEYMAP
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+    SRC := $(KEYMAP_FILE)_plain.c $(SRC)
+endif
 
 
 # Optimize size but this may cause error "relocation truncated to fit"