fc660c: Add initial files

[max/tmk_keyboard.git] / keyboard / fc660c / Makefile

diff --git a/keyboard/fc660c/Makefile b/keyboard/fc660c/Makefile
new file mode 100644 (file)
index 0000000..a926beb
--- /dev/null
+++ b/keyboard/fc660c/Makefile
@@ -0,0 +1,116 @@
+# Target name
+TARGET ?= fc660c
+
+# Location of tmk_core
+TMK_DIR ?= ../../tmk_core
+
+# Location of target dependent files exist
+TARGET_DIR ?= .
+
+
+# List C source files
+SRC ?= matrix.c \
+       led.c
+
+# Configure file
+CONFIG_H ?= config.h
+
+
+# MCU name
+MCU ?= atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU ?= 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096      (TMK Alt Controller)
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE ?= yes       # Virtual DIP switch configuration
+MOUSEKEY_ENABLE ?= yes         # Mouse keys
+EXTRAKEY_ENABLE ?= yes         # Audio control and System control
+CONSOLE_ENABLE ?= yes          # Console for debug
+COMMAND_ENABLE ?= yes          # Commands for debug and configuration
+NKRO_ENABLE ?= yes             # USB Nkey Rollover
+#HHKB_JP ?= yes                        # HHKB JP support
+#UNIMAP_ENABLE ?= yes          # Universal keymap
+#ACTIONMAP_ENABLE ?= yes       # Use 16bit actionmap instead of 8bit keymap
+#KEYMAP_SECTION_ENABLE ?= yes  # fixed address keymap for keymap editor
+
+#OPT_DEFS += -DNO_ACTION_TAPPING
+#OPT_DEFS += -DNO_ACTION_LAYER
+#OPT_DEFS += -DNO_ACTION_MACRO
+
+
+#
+# Keymap file
+#
+ifeq (yes,$(strip $(UNIMAP_ENABLE)))
+    KEYMAP_FILE = unimap
+else
+    ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
+        KEYMAP_FILE = actionmap
+    else
+        KEYMAP_FILE = keymap
+    endif
+endif
+ifdef KEYMAP
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+    SRC := $(KEYMAP_FILE).c $(SRC)
+endif
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+ifeq (yes,$(strip $(RN42_ENABLE)))
+include rn42.mk
+include $(TMK_DIR)/protocol.mk
+endif
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk