#include "descriptor.h"
#include "lufa.h"
-static uint8_t idle_duration = 0;
-static uint8_t protocol_report = 1;
+uint8_t keyboard_idle = 0;
+uint8_t keyboard_protocol = 1;
static uint8_t keyboard_led_stats = 0;
static report_keyboard_t keyboard_report_sent;
*/
void EVENT_USB_Device_Connect(void)
{
+ /* For battery powered device */
+ if (!USB_IsInitialized) {
+ USB_Init();
+ USB_Device_EnableSOFEvents();
+ }
}
void EVENT_USB_Device_Disconnect(void)
{
+ /* For battery powered device */
+/* TODO: This doesn't work. After several plug in/outs can not be enumerated.
+ if (USB_IsInitialized) {
+ USB_Disable(); // Disable all interrupts
+ USB_Controller_Enable();
+ USB_INT_Enable(USB_INT_VBUSTI);
+ }
+*/
}
void EVENT_USB_Device_Reset(void)
/* Setup Console HID Report Endpoints */
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN,
CONSOLE_EPSIZE, ENDPOINT_BANK_DOUBLE);
+#if 0
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT,
CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
#endif
+#endif
#ifdef NKRO_ENABLE
/* Setup NKRO HID Report Endpoints */
// Interface
switch (USB_ControlRequest.wIndex) {
case KEYBOARD_INTERFACE:
+#ifdef NKRO_ENABLE
+ case NKRO_INTERFACE:
+#endif
Endpoint_ClearSETUP();
while (!(Endpoint_IsOUTReceived())) {
case HID_REQ_GetProtocol:
if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
- Endpoint_ClearSETUP();
- while (!(Endpoint_IsINReady()));
- Endpoint_Write_8(protocol_report);
- Endpoint_ClearIN();
- Endpoint_ClearStatusStage();
+ if (USB_ControlRequest.wIndex == KEYBOARD_INTERFACE) {
+ Endpoint_ClearSETUP();
+ while (!(Endpoint_IsINReady()));
+ Endpoint_Write_8(keyboard_protocol);
+ Endpoint_ClearIN();
+ Endpoint_ClearStatusStage();
+ }
}
break;
case HID_REQ_SetProtocol:
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
- Endpoint_ClearSETUP();
- Endpoint_ClearStatusStage();
+ if (USB_ControlRequest.wIndex == KEYBOARD_INTERFACE) {
+ Endpoint_ClearSETUP();
+ Endpoint_ClearStatusStage();
- protocol_report = ((USB_ControlRequest.wValue & 0xFF) != 0x00);
+ keyboard_protocol = ((USB_ControlRequest.wValue & 0xFF) != 0x00);
+#ifdef NKRO_ENABLE
+ keyboard_nkro = !!keyboard_protocol;
+#endif
+ clear_keyboard();
+ }
}
break;
Endpoint_ClearSETUP();
Endpoint_ClearStatusStage();
- idle_duration = ((USB_ControlRequest.wValue & 0xFF00) >> 8);
+ keyboard_idle = ((USB_ControlRequest.wValue & 0xFF00) >> 8);
}
break;
{
Endpoint_ClearSETUP();
while (!(Endpoint_IsINReady()));
- Endpoint_Write_8(idle_duration);
+ Endpoint_Write_8(keyboard_idle);
Endpoint_ClearIN();
Endpoint_ClearStatusStage();
}
/* Select the Keyboard Report Endpoint */
#ifdef NKRO_ENABLE
if (keyboard_nkro) {
+ /* Report protocol - NKRO */
Endpoint_SelectEndpoint(NKRO_IN_EPNUM);
/* Check if write ready for a polling interval around 1ms */
while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(4);
if (!Endpoint_IsReadWriteAllowed()) return;
+
+ /* Write Keyboard Report Data */
+ Endpoint_Write_Stream_LE(report, NKRO_EPSIZE, NULL);
}
else
#endif
{
+ /* Boot protocol */
Endpoint_SelectEndpoint(KEYBOARD_IN_EPNUM);
/* Check if write ready for a polling interval around 10ms */
while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40);
if (!Endpoint_IsReadWriteAllowed()) return;
- }
- /* Write Keyboard Report Data */
-#ifdef NKRO_ENABLE
- if (keyboard_nkro) {
- Endpoint_Write_Stream_LE(report, NKRO_EPSIZE, NULL);
- }
- else
-#endif
- {
- /* boot mode */
+ /* Write Keyboard Report Data */
Endpoint_Write_Stream_LE(report, KEYBOARD_EPSIZE, NULL);
}
print("Keyboard start.\n");
while (1) {
while (USB_DeviceState == DEVICE_STATE_Suspended) {
- suspend_power_down();
+ suspend_power_down(WDTO_120MS);
if (USB_Device_RemoteWakeupEnabled && suspend_wakeup_condition()) {
USB_Device_SendRemoteWakeup();
}