#include "sleep_led.h"
#endif
#include "suspend.h"
+#include "hook.h"
#include "descriptor.h"
#include "lufa.h"
uint8_t keyboard_idle = 0;
+/* 0: Boot Protocol, 1: Report Protocol(default) */
uint8_t keyboard_protocol = 1;
static uint8_t keyboard_led_stats = 0;
void EVENT_USB_Device_Suspend()
{
print("[S]");
- matrix_power_down();
-#ifdef SLEEP_LED_ENABLE
- sleep_led_enable();
-#endif
+ hook_usb_suspend_entry();
}
void EVENT_USB_Device_WakeUp()
{
print("[W]");
- suspend_wakeup_init();
-
-#ifdef SLEEP_LED_ENABLE
- sleep_led_disable();
- // NOTE: converters may not accept this
- led_set(host_keyboard_leds());
-#endif
+ hook_usb_wakeup();
}
#ifdef CONSOLE_ENABLE
/** Event handler for the USB_ConfigurationChanged event.
* This is fired when the host sets the current configuration of the USB device after enumeration.
+ *
+ * ATMega32u2 supports dual bank(ping-pong mode) only on endpoint 3 and 4,
+ * it is safe to use singl bank for all endpoints.
*/
void EVENT_USB_Device_ConfigurationChanged(void)
{
#ifdef CONSOLE_ENABLE
/* Setup Console HID Report Endpoints */
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN,
- CONSOLE_EPSIZE, ENDPOINT_BANK_DOUBLE);
+ CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
#if 0
ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT,
CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
Endpoint_ClearSETUP();
Endpoint_ClearStatusStage();
- keyboard_protocol = ((USB_ControlRequest.wValue & 0xFF) != 0x00);
-#ifdef NKRO_ENABLE
- keyboard_nkro = !!keyboard_protocol;
-#endif
+ keyboard_protocol = (USB_ControlRequest.wValue & 0xFF);
clear_keyboard();
}
}
/* Select the Keyboard Report Endpoint */
#ifdef NKRO_ENABLE
- if (keyboard_nkro) {
+ if (keyboard_protocol && keyboard_nkro) {
/* Report protocol - NKRO */
Endpoint_SelectEndpoint(NKRO_IN_EPNUM);
int main(void)
{
setup_mcu();
+ hook_early_init();
keyboard_setup();
setup_usb();
sei();
#endif
print("Keyboard start.\n");
+ hook_late_init();
while (1) {
while (USB_DeviceState == DEVICE_STATE_Suspended) {
print("[s]");
- suspend_power_down();
- if (USB_Device_RemoteWakeupEnabled && suspend_wakeup_condition()) {
- USB_Device_SendRemoteWakeup();
- }
+ hook_usb_suspend_loop();
}
keyboard_task();
#endif
}
}
+
+
+/* hooks */
+__attribute__((weak))
+void hook_early_init(void) {}
+
+__attribute__((weak))
+void hook_late_init(void) {}
+
+ __attribute__((weak))
+void hook_usb_suspend_entry(void)
+{
+#ifdef SLEEP_LED_ENABLE
+ sleep_led_enable();
+#endif
+}
+
+__attribute__((weak))
+void hook_usb_suspend_loop(void)
+{
+ suspend_power_down();
+ if (USB_Device_RemoteWakeupEnabled && suspend_wakeup_condition()) {
+ USB_Device_SendRemoteWakeup();
+ }
+}
+
+__attribute__((weak))
+void hook_usb_wakeup(void)
+{
+ suspend_wakeup_init();
+#ifdef SLEEP_LED_ENABLE
+ sleep_led_disable();
+ // NOTE: converters may not accept this
+ led_set(host_keyboard_leds());
+#endif
+}