X-Git-Url: https://git.friedersdorff.com/?a=blobdiff_plain;f=converter%2Fadb_usb%2FMakefile;h=14fc181ba96fa194a50cf4fbaa62d595e4de94c9;hb=527bdbbcbddc51b22c4fb210889998d550544189;hp=09f30180a83d7124c4bbcd0bc1b4bd84abdb841e;hpb=3fa50565af7ad72e895183c5caeb51591c69a45e;p=max%2Ftmk_keyboard.git

diff --git a/converter/adb_usb/Makefile b/converter/adb_usb/Makefile
index 09f30180..14fc181b 100644
--- a/converter/adb_usb/Makefile
+++ b/converter/adb_usb/Makefile
@@ -1,41 +1,67 @@
 # Target file name (without extension).
-TARGET = adb_usb
+TARGET ?= adb_usb
 
 # Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
-# keyboard dependent files
-SRC =	keymap.c \
-	matrix.c \
+# project specific files
+SRC ?=	matrix.c \
 	led.c \
 	adb.c
 
 CONFIG_H = config.h
 
 
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
+# MCU name
+# atmega32u4 	Teensy2.0
+# atemga32u4	TMK Converter rev.1
+# atemga32u2	TMK Converter rev.2
+MCU ?= atmega32u2
 
 # Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU ?= 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
 
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
 #   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
+#   Atmel DFU loader 4096	for TMK Converter rev.1/rev.2
 #   LUFA bootloader  4096
 #   USBaspLoader     2048
 OPT_DEFS += -DBOOTLOADER_SIZE=4096
@@ -45,19 +71,49 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 #   comment out to disable the options.
 #
 #BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-#MOUSEKEY_ENABLE = yes	# Mouse keys(+5000)
-#EXTRAKEY_ENABLE = yes	# Audio control and System control(+600)
-#CONSOLE_ENABLE = yes    # Console for debug
-#COMMAND_ENABLE = yes    # Commands for debug and configuration
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover(+500)
+#NKRO_ENABLE = yes	# USB Nkey Rollover
+ADB_MOUSE_ENABLE = yes
+#UNIMAP_ENABLE = yes
+#ACTIONMAP_ENABLE = yes         # Use 16bit actionmap instead of 8bit keymap
+#KEYMAP_SECTION_ENABLE = yes	# fixed address keymap for keymap editor
+
+# ADB Mice need acceleration for todays much bigger screens. 
+OPT_DEFS += -DADB_MOUSE_MAXACC=8
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+    KEYMAP_FILE = unimap
+else
+    ifdef ACTIONMAP_ENABLE
+	KEYMAP_FILE = actionmap
+    else
+	KEYMAP_FILE = keymap
+    endif
+endif
+ifdef KEYMAP
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+    SRC := $(KEYMAP_FILE)_plain.c $(SRC)
+endif
 
 
 # Search Path
 VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
 
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk