X-Git-Url: https://git.friedersdorff.com/?a=blobdiff_plain;f=converter%2Fps2_usb%2FMakefile;h=f20039c6f07c9f70b8f2a896166700f227b63cd8;hb=b316f19871ab39e6a75146d74a3b5cca37165f3c;hp=0c6442374c4cca13cbff297148aa92b2a7c04d3c;hpb=fce750a1767ed86e0967eacf075a9cd59cbf306c;p=max%2Ftmk_keyboard.git diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile index 0c644237..f20039c6 100644 --- a/converter/ps2_usb/Makefile +++ b/converter/ps2_usb/Makefile @@ -1,5 +1,8 @@ +# +# Makefile for Teensy +# # Target file name (without extension). -TARGET = ps2_usb +TARGET = ps2_usb_lufa # Directory common source filess exist TOP_DIR = ../.. @@ -7,69 +10,109 @@ TOP_DIR = ../.. # Directory keyboard dependent files exist TARGET_DIR = . +# project specific files +SRC = keymap_common.c \ + matrix.c \ + led.c + +ifdef KEYMAP + SRC := keymap_$(KEYMAP).c $(SRC) +else + SRC := keymap_plain.c $(SRC) +endif + +CONFIG_H = config.h -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 # Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. F_CPU = 16000000 -# Build Options -# *Comment out* to disable the options. # -MOUSEKEY_ENABLE = yes # Mouse keys -EXTRAKEY_ENABLE = yes # Audio control and System control -NKRO_ENABLE = yes # USB Nkey Rollover +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) -PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) -#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin -#PS2_USE_BUSYWAIT = yes # uses primitive reference code +# Interrupt driven control endpoint task(+60) +#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ - led.c +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 -ifdef PS2_USE_USART - SRC += protocol/ps2_usart.c - OPT_DEFS += -DPS2_USE_USART -endif -ifdef PS2_USE_INT - SRC += protocol/ps2.c - OPT_DEFS += -DPS2_USE_INT -endif -ifdef PS2_USE_BUSYWAIT - SRC += protocol/ps2.c - OPT_DEFS += -DPS2_USE_BUSYWAIT -endif +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -#CONFIG_H = config_pjrc_usart.h -CONFIG_H = config.h +# PS/2 Options +# +PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) +#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin +#PS2_USE_BUSYWAIT = yes # uses primitive reference code +# Serial Mouse Options +# You can choose a mouse protocol and the implementation of +# the underlying serial connection. +# +#SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice +#SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice +#SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection +#SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation -#---------------- Programming Options -------------------------- -PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex +# Optional serial mouse driver features +# Support scrolling while holding the middle mouse button +# (currently only supported for Mousesystems mice): +#OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax # Search Path VPATH += $(TARGET_DIR) VPATH += $(TOP_DIR) - -include $(TOP_DIR)/protocol/pjrc.mk include $(TOP_DIR)/protocol.mk +include $(TOP_DIR)/protocol/lufa.mk include $(TOP_DIR)/common.mk include $(TOP_DIR)/rules.mk