X-Git-Url: https://git.friedersdorff.com/?a=blobdiff_plain;f=converter%2Fsun_usb%2FMakefile;h=12eceb5e74fc0f348c86c7c649cf0ca9b6502431;hb=3fe8e1c238fc8e15dacda1b03c0c1745a7b8e8e7;hp=7c06f26ce80a9668c8f381613742b40411ccb578;hpb=97ee1be59da06063275d315d1ea5fa4f14eee6b0;p=max%2Ftmk_keyboard.git

diff --git a/converter/sun_usb/Makefile b/converter/sun_usb/Makefile
index 7c06f26c..12eceb5e 100644
--- a/converter/sun_usb/Makefile
+++ b/converter/sun_usb/Makefile
@@ -1,13 +1,8 @@
-#
-# Makefile for PJRC Teensy
-#
-
-
 # Target file name (without extension).
 TARGET = sun_usb
 
 # Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR = ../../tmk_core
 
 # Directory keyboard dependent files exist
 TARGET_DIR = .
@@ -16,7 +11,8 @@ TARGET_DIR = .
 SRC =	keymap.c \
 	matrix.c \
 	led.c \
-	protocol/serial.c
+	command_extra.c
+
 
 CONFIG_H = config.h
 
@@ -24,9 +20,10 @@ CONFIG_H = config.h
 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
 #MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
+#MCU = atmega32u4       # Teensy 2.0
 #MCU = at90usb646       # Teensy++ 1.0
 #MCU = at90usb1286      # Teensy++ 2.0
+MCU = atmega32u2
 
 
 # Processor frequency.
@@ -37,54 +34,59 @@ MCU = atmega32u4       # Teensy 2.0
 F_CPU = 16000000
 
 
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
 # Build Options
 #   *Comment out* to disable the options.
 #
 MOUSEKEY_ENABLE = yes	# Mouse keys
 EXTRAKEY_ENABLE = yes	# Audio control and System control
-NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-AVRDUDE = avrdude
-# Type: avrdude -c ? to get a full listing.
-AVRDUDE_PROGRAMMER = avr109
-AVRDUDE_PORT = /dev/ttyACM0
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level.  Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
+CONSOLE_ENABLE = yes	# Console for debug
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#HARDWARE_SERIAL = yes  # Use hardware serial (requires inverted serial, see README)
+#NKRO_ENABLE = yes	# USB Nkey Rollover
 
-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+ifdef HARDWARE_SERIAL
+	SRC := protocol/serial_uart.c $(SRC)
+	OPT_DEFS += -DHARDWARE_SERIAL
+else
+	SRC := protocol/serial_soft.c $(SRC)
+endif
 
-#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
 
 
 # Search Path
 VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
 
 
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk