X-Git-Url: https://git.friedersdorff.com/?a=blobdiff_plain;f=keyboard%2Fhhkb%2FMakefile.rn42;h=bf4960c2e2619d8a1868f9576f327de397515bf7;hb=ab083c7ecff4f8a576d858745ab353f7937a1b94;hp=cbb2b744c9652db6bb22f571b69c9ef7fa010fbe;hpb=5ce9bf8353568b341b79b3cea676ea62a7d40442;p=max%2Ftmk_keyboard.git

diff --git a/keyboard/hhkb/Makefile.rn42 b/keyboard/hhkb/Makefile.rn42
index cbb2b744..bf4960c2 100644
--- a/keyboard/hhkb/Makefile.rn42
+++ b/keyboard/hhkb/Makefile.rn42
@@ -1,155 +1,5 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = hhkb_rn42
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-
-# List C source files here. (C dependencies are automatically generated.)
-SRC +=	keymap_common.c \
-	matrix.c \
-	led.c
-
-CONFIG_H = config_rn42.h
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096	(TMK Alt Controller)
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes		# Virtual DIP switch configuration
-MOUSEKEY_ENABLE = yes		# Mouse keys
-EXTRAKEY_ENABLE = yes		# Audio control and System control
-CONSOLE_ENABLE = yes		# Console for debug
-COMMAND_ENABLE = yes    	# Commands for debug and configuration
-#NKRO_ENABLE = yes		# USB Nkey Rollover
-#KEYMAP_SECTION_ENABLE = yes	# fixed address keymap for keymap editor
-#HHKB_JP = yes			# HHKB JP support
-
-
-#
-# Keymap file
-#
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    ifdef HHKB_JP
-    	SRC := keymap_jp.c $(SRC)
-    else 
-    	SRC := keymap_hhkb.c $(SRC)
-    endif
-endif
-
-
-ifneq (, $(or $(findstring keymap_jp.c, $(SRC)), $(findstring yes, $(HHKB_JP))))
-    OPT_DEFS += -DHHKB_JP
-endif
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include rn42.mk
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
-
-debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
-debug-on: all
-
-debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
-debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
-debug-off: all
+TARGET ?= hhkb_rn42
+CONFIG_H ?= config_rn42.h
+RN42_ENABLE ?= yes
+NKRO_ENABLE ?= yes
+include Makefile