X-Git-Url: https://git.friedersdorff.com/?a=blobdiff_plain;f=orphan%2Fghost_squid%2FMakefile.lufa;fp=orphan%2Fghost_squid%2FMakefile.lufa;h=54adb1e3d818537a7745f3dd7abbfe29c9dec399;hb=885e7adb18fb6039f0fe66de23e0622af923f7d1;hp=0000000000000000000000000000000000000000;hpb=5c277a6687b63f34e5d5696365a2ed88e48441f2;p=max%2Ftmk_keyboard.git

diff --git a/orphan/ghost_squid/Makefile.lufa b/orphan/ghost_squid/Makefile.lufa
new file mode 100644
index 00000000..54adb1e3
--- /dev/null
+++ b/orphan/ghost_squid/Makefile.lufa
@@ -0,0 +1,117 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = ghostsquid_lufa
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC =	keymap.c \
+	matrix.c \
+	led.c
+
+CONFIG_H = config.h
+
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+#CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk