+++ /dev/null
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-# Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-# have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-# have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-# (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-# (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-# with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-# bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = hhkb_lufa
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-
-# List C source files here. (C dependencies are automatically generated.)
-SRC += keymap_common.c \
- matrix.c \
- led.c
-
-ifdef KEYMAP
- SRC := keymap_$(KEYMAP).c $(SRC)
-else
- SRC := keymap_hasu.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-
-# MCU name
-# PJRC Teensy++ 2.0
-#MCU = at90usb1286
-# TMK Alt Controller or PJRC Teensy 2.0
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096 (TMK Alt Controller)
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
-MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes # Audio control and System control
-#CONSOLE_ENABLE = yes # Console for debug
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = yes # USB Nkey Rollover
-KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-include $(TOP_DIR)/protocol/lufa.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
-
-debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
-debug-on: all
-
-debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
-debug-off: all
#----------------------------------------------------------------------------
# Target file name (without extension).
-TARGET = hhkb_lufa
+TARGET = hhkb_rn42
# Directory common source filess exist
TOP_DIR = ../..
matrix.c \
led.c
-CONFIG_H = config.h
+CONFIG_H = config_rn42.h
# MCU name
-# PJRC Teensy++ 2.0
-#MCU = at90usb1286
-# TMK Alt Controller or PJRC Teensy 2.0
MCU = atmega32u4
# Processor frequency.
#HHKB_JP = yes # HHKB JP support
-ifdef HHKB_JP
- OPT_DEFS += -DHHKB_JP
-endif
-
-
#
# Keymap file
#
else
ifdef HHKB_JP
SRC := keymap_jp.c $(SRC)
- else
- SRC := keymap_hasu.c $(SRC)
+ else
+ SRC := keymap_hhkb.c $(SRC)
endif
endif
+ifneq (, $(or $(findstring keymap_jp.c, $(SRC)), $(findstring yes, $(HHKB_JP))))
+ OPT_DEFS += -DHHKB_JP
+endif
+
+
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
debug-on: all
debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
+debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
debug-off: all
[AltController]: http://geekhack.org/index.php?topic=12047.0
+## Update
+* Bluetooth module RN-42 is supported.(2015/01)
+* V-USB and iWRAP are no longer supported now, but still it'll works with a little fix. See not_supported directory.(2015/01)
+
+
##Features
* Customizable keymap
* More keymap layers(more Fn keys)
* Mouse keys
* USB NKRO
+* Bluetooth(RN-42)
See README of [tmk_keyboard] for more.
### Build
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. Just `make` with `KEYMAP` option like:
- $ make KEYMAP=[hasu|hhkb|spacefn|<name>]
- $ make -f Makefile.jp KEYMAP=[jp|<name>] # for HHKB JP
+ $ make -f Makefile.<jp|pjrc|rn42> KEYMAP=(hasu|hhkb|spacefn|<name>)
+
+You can omit `-f` option when you use `Makefile`. `Makefile` is used for **Pro2 and Pro**, `Makefile.jp` fits for **JP** model and `Makefile.rn42` supports Bluetooth module **RN-42**. `Makefile.pjrc` uses **PJRC** as output protocol instead of **LUFA**.
### Program
This command programs the controller with [dfu-programmer] if the tool is installed and configured properly.
- $ make dfu
- $ make -f Makefile.jp dfu # for HHKB JP
+ $ make -f Makefile.<variant> KEYMAP=<name> dfu
Or you can also use [FLIP] command to program. Also the tool should be installed and configured properly. FLIP GUI application is also available.
- $ make flip
- $ make -f Makefile.jp flip # for HHKB JP
+ $ make -f Makefile.<variant> KEYMAP=<name> flip
Use [Teensy Loader] if your controller is Teensy/Teensy++.
static inline bool KEY_STATE(void) { return (PIND & (1<<7)); }
static inline void KEY_PREV_ON(void) { (PORTB |= (1<<7)); }
static inline void KEY_PREV_OFF(void) { (PORTB &= ~(1<<7)); }
+#ifdef HHKB_POWER_SAVING
+static inline void KEY_POWER_ON(void) {
+ DDRB = 0xFF; PORTB = 0x40; // change pins output
+ DDRD |= (1<<4); PORTD |= (1<<4); // MOS FET switch on
+ /* Without this wait you will miss or get false key events. */
+ _delay_ms(5); // wait for powering up
+}
+static inline void KEY_POWER_OFF(void) {
+ /* input with pull-up consumes less than without it when pin is open. */
+ DDRB = 0x00; PORTB = 0xFF; // change pins input with pull-up
+ DDRD |= (1<<4); PORTD &= ~(1<<4); // MOS FET switch off
+}
+static inline bool KEY_POWER_STATE(void) { return PORTD & (1<<4); }
+#else
static inline void KEY_POWER_ON(void) {}
static inline void KEY_POWER_OFF(void) {}
+static inline bool KEY_POWER_STATE(void) { return true; }
+#endif
static inline void KEY_INIT(void)
{
+ /* row,col,prev: output */
DDRB = 0xFF;
- PORTB = 0x00;
+ PORTB = 0x40; // unable
+ /* key: input with pull-up */
DDRD &= ~0x80;
- PORTD |= 0x80;
- /* keyswitch board power on */
- DDRD |= (1<<4);
- PORTD |= (1<<4);
+ PORTD |= 0x80;
#ifdef HHKB_JP
/* row extention for HHKB JP */
DDRC |= (1<<6|1<<7);
#endif
KEY_UNABLE();
KEY_PREV_OFF();
+
+ KEY_POWER_OFF();
}
static inline void KEY_SELECT(uint8_t ROW, uint8_t COL)
{
#define KEY_PREV_OFF() (PORTE &= ~(1<<7))
#define KEY_POWER_ON()
#define KEY_POWER_OFF()
+#define KEY_POWER_STATE() true
#else
#include "timer.h"
#include "matrix.h"
#include "hhkb_avr.h"
+#include <avr/wdt.h>
+#include "suspend.h"
+#include "lufa.h"
+// matrix power saving
+#define MATRIX_POWER_SAVE 10000
+static uint32_t matrix_last_modified = 0;
+
// matrix state buffer(1:on, 0:off)
static matrix_row_t *matrix;
static matrix_row_t *matrix_prev;
matrix_prev = matrix;
matrix = tmp;
- KEY_POWER_ON();
+ // power on
+ if (!KEY_POWER_STATE()) KEY_POWER_ON();
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
for (uint8_t col = 0; col < MATRIX_COLS; col++) {
KEY_SELECT(row, col);
// This takes 25us or more to make sure KEY_STATE returns to idle state.
_delay_us(75);
}
+ if (matrix[row] ^ matrix_prev[row]) matrix_last_modified = timer_read32();
+ }
+ // power off
+ if (KEY_POWER_STATE() &&
+ (USB_DeviceState == DEVICE_STATE_Suspended ||
+ USB_DeviceState == DEVICE_STATE_Unattached ) &&
+ timer_elapsed32(matrix_last_modified) > MATRIX_POWER_SAVE) {
+ KEY_POWER_OFF();
+ suspend_power_down();
}
- KEY_POWER_OFF();
return 1;
}
xprintf("%02X: %08b\n", row, bitrev(matrix_get_row(row)));
}
}
+
+void matrix_power_up(void) {
+ KEY_POWER_ON();
+}
+void matrix_power_down(void) {
+ KEY_POWER_OFF();
+}
+++ /dev/null
-#ifndef HHKB_AVR_H
-#define HHKB_AVR_H
-
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/io.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-
-
-// Timer resolution check
-#if (1000000/TIMER_RAW_FREQ > 20)
-# error "Timer resolution(>20us) is not enough for HHKB matrix scan tweak on V-USB."
-#endif
-
-
-/*
- * HHKB Matrix I/O
- *
- * row: HC4051[A,B,C] selects scan row0-7
- * row-ext: [En0,En1] row extention for JP
- * col: LS145[A,B,C,D] selects scan col0-7 and enable(D)
- * key: on: 0/off: 1
- * prev: hysteresis control: assert(1) when previous key state is on
- */
-
-
-#if defined(__AVR_ATmega32U4__)
-/*
- * For TMK HHKB alt controller(ATMega32U4)
- *
- * row: PB0-2
- * col: PB3-5,6
- * key: PD7(pull-uped)
- * prev: PB7
- * power: PD4(L:off/H:on)
- * row-ext: PC6,7 for HHKB JP(active low)
- */
-static inline void KEY_ENABLE(void) { (PORTB &= ~(1<<6)); }
-static inline void KEY_UNABLE(void) { (PORTB |= (1<<6)); }
-static inline bool KEY_STATE(void) { return (PIND & (1<<7)); }
-static inline void KEY_PREV_ON(void) { (PORTB |= (1<<7)); }
-static inline void KEY_PREV_OFF(void) { (PORTB &= ~(1<<7)); }
-#ifdef HHKB_POWER_SAVING
-static inline void KEY_POWER_ON(void) {
- DDRB = 0xFF; PORTB = 0x40; // change pins output
- DDRD |= (1<<4); PORTD |= (1<<4); // MOS FET switch on
- /* Without this wait you will miss or get false key events. */
- _delay_ms(5); // wait for powering up
-}
-static inline void KEY_POWER_OFF(void) {
- /* input with pull-up consumes less than without it when pin is open. */
- DDRB = 0x00; PORTB = 0xFF; // change pins input with pull-up
- DDRD |= (1<<4); PORTD &= ~(1<<4); // MOS FET switch off
-}
-static inline bool KEY_POWER_STATE(void) { return PORTD & (1<<4); }
-#else
-static inline void KEY_POWER_ON(void) {}
-static inline void KEY_POWER_OFF(void) {}
-static inline bool KEY_POWER_STATE(void) { return true; }
-#endif
-static inline void KEY_INIT(void)
-{
- /* row,col,prev: output */
- DDRB = 0xFF;
- PORTB = 0x40; // unable
- /* key: input with pull-up */
- DDRD &= ~0x80;
- PORTD |= 0x80;
-#ifdef HHKB_JP
- /* row extention for HHKB JP */
- DDRC |= (1<<6|1<<7);
- PORTC |= (1<<6|1<<7);
-#endif
- KEY_UNABLE();
- KEY_PREV_OFF();
-
- KEY_POWER_OFF();
-}
-static inline void KEY_SELECT(uint8_t ROW, uint8_t COL)
-{
- PORTB = (PORTB & 0xC0) | (((COL) & 0x07)<<3) | ((ROW) & 0x07);
-#ifdef HHKB_JP
- if ((ROW) & 0x08) PORTC = (PORTC & ~(1<<6|1<<7)) | (1<<6);
- else PORTC = (PORTC & ~(1<<6|1<<7)) | (1<<7);
-#endif
-}
-
-
-#elif defined(__AVR_AT90USB1286__)
-/*
- * For Teensy++(AT90USB1286)
- *
- * HHKB pro HHKB pro2
- * row: PB0-2 (6-8) (5-7)
- * col: PB3-5,6 (9-12) (8-11)
- * key: PE6(pull-uped) (4) (3)
- * prev: PE7 (5) (4)
- *
- * TODO: convert into 'staitc inline' function
- */
-#define KEY_INIT() do { \
- DDRB |= 0x7F; \
- DDRE |= (1<<7); \
- DDRE &= ~(1<<6); \
- PORTE |= (1<<6); \
-} while (0)
-#define KEY_SELECT(ROW, COL) (PORTB = (PORTB & 0xC0) | \
- (((COL) & 0x07)<<3) | \
- ((ROW) & 0x07))
-#define KEY_ENABLE() (PORTB &= ~(1<<6))
-#define KEY_UNABLE() (PORTB |= (1<<6))
-#define KEY_STATE() (PINE & (1<<6))
-#define KEY_PREV_ON() (PORTE |= (1<<7))
-#define KEY_PREV_OFF() (PORTE &= ~(1<<7))
-#define KEY_POWER_ON()
-#define KEY_POWER_OFF()
-
-
-#else
-# error "define code for matrix scan"
-#endif
-
-
-#if 0
-// For ATMega328P with V-USB
-//
-// #elif defined(__AVR_ATmega328P__)
-// Ports for V-USB
-// key: PB0(pull-uped)
-// prev: PB1
-// row: PB2-4
-// col: PC0-2,3
-// power: PB5(Low:on/Hi-z:off)
-#define KEY_INIT() do { \
- DDRB |= 0x3E; \
- DDRB &= ~(1<<0); \
- PORTB |= 1<<0; \
- DDRC |= 0x0F; \
- KEY_UNABLE(); \
- KEY_PREV_OFF(); \
-} while (0)
-#define KEY_SELECT(ROW, COL) do { \
- PORTB = (PORTB & 0xE3) | ((ROW) & 0x07)<<2; \
- PORTC = (PORTC & 0xF8) | ((COL) & 0x07); \
-} while (0)
-#define KEY_ENABLE() (PORTC &= ~(1<<3))
-#define KEY_UNABLE() (PORTC |= (1<<3))
-#define KEY_STATE() (PINB & (1<<0))
-#define KEY_PREV_ON() (PORTB |= (1<<1))
-#define KEY_PREV_OFF() (PORTB &= ~(1<<1))
-// Power supply switching
-#define KEY_POWER_ON() do { \
- KEY_INIT(); \
- PORTB &= ~(1<<5); \
- _delay_ms(1); \
-} while (0)
-#define KEY_POWER_OFF() do { \
- DDRB &= ~0x3F; \
- PORTB &= ~0x3F; \
- DDRC &= ~0x0F; \
- PORTC &= ~0x0F; \
-} while (0)
-#endif
-
-#endif
+++ /dev/null
-/*
-Copyright 2012,2013 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-#include <stdint.h>
-#include "action.h"
-#include <avr/pgmspace.h>
-#include "keymap_common.h"
-
-
-/* translates key to keycode */
-uint8_t keymap_key_to_keycode(uint8_t layer, keypos_t key)
-{
- return pgm_read_byte(&keymaps[(layer)][(key.row)][(key.col)]);
-}
-
-/* translates Fn keycode to action */
-action_t keymap_fn_to_action(uint8_t keycode)
-{
- return (action_t){ .code = pgm_read_word(&fn_actions[FN_INDEX(keycode)]) };
-}
+++ /dev/null
-/*
-Copyright 2012,2013 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-#ifndef KEYMAP_COMMON_H
-#define KEYMAP_COMMON_H
-
-#include <stdint.h>
-#include <stdbool.h>
-#include "keycode.h"
-#include "action.h"
-#include "action_code.h"
-#include "action_layer.h"
-#include "action_macro.h"
-#include "action_util.h"
-#include "report.h"
-#include "host.h"
-#include "print.h"
-#include "debug.h"
-#include "keymap.h"
-
-
-extern const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS];
-extern const uint16_t fn_actions[];
-
-
-#define KEYMAP( \
- K31, K30, K00, K10, K11, K20, K21, K40, K41, K60, K61, K70, K71, K50, K51, \
- K32, K01, K02, K13, K12, K23, K22, K42, K43, K62, K63, K73, K72, K52, \
- K33, K04, K03, K14, K15, K24, K25, K45, K44, K65, K64, K74, K53, \
- K34, K05, K06, K07, K16, K17, K26, K46, K66, K76, K75, K55, K54, \
- K35, K36, K37, K57, K56 \
-) \
-{ \
- { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
- { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
- { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_NO }, \
- { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
- { KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_##K45, KC_##K46, KC_NO }, \
- { KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
- { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_NO }, \
- { KC_##K70, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_NO } \
-}
-
-
-#define KEYMAP_JP( \
- K02, K32, K62, K22, K12, K52, K72, KA2, K92, K82, KB2, KE2, KF2, KD2, KC2, \
- K03, K63, K23, K13, K53, K73, KA3, K93, K83, KB3, KE3, KF3, KD3, \
- K06, K66, K26, K16, K56, K76, KA6, K96, K86, KB6, KE6, KF6, KD6, KC6, \
- K05, K65, K25, K15, K55, K75, KA5, K95, K85, KB5, KE5, KF5, KD5, KC5, \
- K04, K34, K64, K24, K14, K74, K94, K84, KB4, KE4, KF4, KD4, KC4 \
-) \
-{ \
- { KC_NO, KC_NO, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_NO }, \
- { KC_NO, KC_NO, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_NO }, \
- { KC_NO, KC_NO, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_NO }, \
- { KC_NO, KC_NO, KC_##K32, KC_NO, KC_##K34, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
- { KC_NO, KC_NO, KC_##K52, KC_##K53, KC_NO, KC_##K55, KC_##K56, KC_NO }, \
- { KC_NO, KC_NO, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_NO }, \
- { KC_NO, KC_NO, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_NO }, \
- { KC_NO, KC_NO, KC_##K82, KC_##K83, KC_##K84, KC_##K85, KC_##K86, KC_NO }, \
- { KC_NO, KC_NO, KC_##K92, KC_##K93, KC_##K94, KC_##K95, KC_##K96, KC_NO }, \
- { KC_NO, KC_NO, KC_##KA2, KC_##KA3, KC_NO, KC_##KA5, KC_##KA6, KC_NO }, \
- { KC_NO, KC_NO, KC_##KB2, KC_##KB3, KC_##KB4, KC_##KB5, KC_##KB6, KC_NO }, \
- { KC_NO, KC_NO, KC_##KC2, KC_NO, KC_##KC4, KC_##KC5, KC_##KC6, KC_NO }, \
- { KC_NO, KC_NO, KC_##KD2, KC_##KD3, KC_##KD4, KC_##KD5, KC_##KD6, KC_NO }, \
- { KC_NO, KC_NO, KC_##KE2, KC_##KE3, KC_##KE4, KC_##KE5, KC_##KE6, KC_NO }, \
- { KC_NO, KC_NO, KC_##KF2, KC_##KF3, KC_##KF4, KC_##KF5, KC_##KF6, KC_NO } \
-}
-
-#endif
+++ /dev/null
-/*
- * Hasu: my personal keymap
- */
-#include "keymap_common.h"
-
-
-#ifdef KEYMAP_SECTION_ENABLE
-const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] __attribute__ ((section (".keymap.keymaps"))) = {
-#else
-const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] PROGMEM = {
-#endif
- /* Layer 0: Default Layer
- * ,-----------------------------------------------------------.
- * |Esc| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =| \| `|
- * |-----------------------------------------------------------|
- * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]|Backs|
- * |-----------------------------------------------------------|
- * |Contro| A| S| D| F| G| H| J| K| L|Fn3| '|Fn6 |
- * |-----------------------------------------------------------|
- * |Fn7 | Z| X| C| V| B| N| M| ,| .|Fn2|Shift |Fn1|
- * `-----------------------------------------------------------'
- * |Gui|Alt | Fn4 |Fn5 |Gui|
- * `-------------------------------------------'
- */
- [0] = \
- KEYMAP(ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSLS,GRV, \
- TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSPC, \
- LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT,FN6, \
- FN7, Z, X, C, V, B, N, M, COMM,DOT, FN2, RSFT,FN1, \
- LGUI,LALT, FN4, FN5, RGUI),
-
- /* Layer 1: HHKB mode[HHKB Fn]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Caps | | | | | | | |Psc|Slk|Pus|Up | |Backs|
- * |-----------------------------------------------------------|
- * |Contro|VoD|VoU|Mut| | | *| /|Hom|PgU|Lef|Rig|Enter |
- * |-----------------------------------------------------------|
- * |Shift | | | | | | +| -|End|PgD|Dow|Shift | |
- * `-----------------------------------------------------------'
- * |Gui|Alt | Space |Alt |Gui|
- * `-------------------------------------------'
- */
- [1] = \
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,PAUS, UP, NO, BSPC, \
- LCTL,VOLD,VOLU,MUTE,NO, NO, PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \
- LSFT,NO, NO, NO, NO, NO, PPLS,PMNS,END, PGDN,DOWN,RSFT,TRNS, \
- LGUI,LALT, TRNS, RALT,RGUI),
-
- /* Layer 2: Vi mode[Slash]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab |Hom|PgD|Up |PgU|End|Hom|PgD|PgUlEnd| | | |Backs|
- * |-----------------------------------------------------------|
- * |Contro| |Lef|Dow|Rig| |Lef|Dow|Up |Rig| | |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | | |Hom|PgD|PgUlEnd|Fn0|Shift | |
- * `-----------------------------------------------------------'
- * |Gui|Alt | Space |Alt |Gui|
- * `-------------------------------------------'
- */
- [2] = \
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- TAB, HOME,PGDN,UP, PGUP,END, HOME,PGDN,PGUP,END, NO, NO, NO, BSPC, \
- LCTL,NO, LEFT,DOWN,RGHT,NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, \
- LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN2, RSFT,TRNS, \
- LGUI,LALT, SPC, RALT,RGUI),
-
- /* Layer 3: Mouse mode(IJKL)[Semicolon]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab | | | | | |MwL|MwD|McU|MwU|MwR|Wbk|Wfr|Alt-T|
- * |-----------------------------------------------------------|
- * |Contro| | | | | |Mb2|McL|McD|McR|Fn | |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Mb1 |Fn |Fn |
- * `--------------------------------------------'
- * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
- */
- [3] = \
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- FN8, NO, NO, NO, NO, NO, NO, WH_D,MS_U,WH_U,RGHT,FN9, FN10,FN8, \
- LCTL,ACL0,ACL1,ACL2,ACL2,NO, NO, MS_L,MS_D,MS_R,FN3, NO, ENT, \
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,FN9, FN10,NO, RSFT,TRNS, \
- LGUI,LALT, BTN1, TRNS,TRNS),
-
- /* Layer 4: Mouse mode(IJKL)[Space]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab | | | | | |MwL|MwD|McU|MwU|MwR|Wbk|Wfr|Alt-T|
- * |-----------------------------------------------------------|
- * |Contro| | | | | |Mb2|McL|McD|McR|Mb1| |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Mb1 |Fn |Fn |
- * `--------------------------------------------'
- * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
- */
- [4] = \
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- FN8, NO, NO, NO, NO, NO, NO, WH_D,MS_U,WH_U,RGHT,FN9, FN10,FN8, \
- LCTL,VOLD,VOLU,MUTE,NO, NO, NO, MS_L,MS_D,MS_R,BTN1,NO, ENT, \
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,FN9, FN10,NO, RSFT,TRNS, \
- LGUI,LALT, TRNS, TRNS,TRNS),
-
-#if 0
- /* Layer 3: Mouse mode(HJKL)[Semicolon]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab | | | | | |MwL|MwD|MwU|MwR| | | |Backs|
- * |-----------------------------------------------------------|
- * |Contro| | | | | |McL|McD|McU|McR|Fn0| |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Mb1 |Alt |Fn0|
- * `--------------------------------------------'
- * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
- */
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- TAB, NO, NO, NO, NO, NO, NO, WH_D,WH_U,RGHT,NO, NO, NO, BSPC, \
- LCTL,NO, ACL0,ACL1,ACL2,NO, MS_L,MS_D,MS_U,MS_R,TRNS,QUOT,ENT, \
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,FN9, FN10,SLSH,RSFT,NO, \
- LGUI,LALT, BTN1, RALT,TRNS),
-
- /* Layer4: Mouse mode(HJKL)[Space]
- * ,-----------------------------------------------------------.
- * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Tab | | | | | |MwL|MwD|MwU|MwR| |Wbk|Wfr|Alt-T|
- * |-----------------------------------------------------------|
- * |Contro| | | | | |McL|McD|McU|McR|Fn0| |Return |
- * |-----------------------------------------------------------|
- * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Fn0 |Alt |Fn0|
- * `--------------------------------------------'
- * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel
- */
- KEYMAP(GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- FN8, NO, NO, NO, NO, NO, NO, WH_D,WH_U,RGHT,NO, FN9, FN10,FN8, \
- LCTL,NO, ACL0,ACL1,ACL2,NO, MS_L,MS_D,MS_U,MS_R,BTN1,NO, ENT, \
- LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,FN9, FN10,NO, RSFT,NO, \
- LGUI,LALT, TRNS, RALT,RGUI),
-#endif
-#if 0
- /* Layer x: Matias half-qwerty keyboard style[Space]
- * ,-----------------------------------------------------------.
- * | -| 0| 9| 8| 7| 6| 5| 4| 3| 2| 1| | | |Esc|
- * |-----------------------------------------------------------|
- * |Backs| P| O| I| U| Y| T| R| E| W| Q| | |Tab |
- * |-----------------------------------------------------------|
- * |Contro| ;| L| K| J| H| G| F| D| S| A|Con|Control |
- * |-----------------------------------------------------------|
- * |Shift | /| .| ,| M| N| B| V| C| X| Z|Shift | |
- * `-----------------------------------------------------------'
- * |Gui |Alt | Fn0 |Alt |Gui|
- * `--------------------------------------------'
- */
- KEYMAP(MINS,0, 9, 8, 7, 6, 5, 4, 3, 2, 1, NO, NO, NO, ESC, \
- BSPC,P, O, I, U, Y, T, R, E, W, Q, NO, NO, TAB, \
- LCTL,SCLN,L, K, J, H, G, F, D, S, A, RCTL,RCTL, \
- LSFT,SLSH,DOT, COMM,M, N, B, V, C, X, Z, RSFT,NO, \
- LGUI,LALT, TRNS, RALT,RGUI),
-#endif
-};
-
-
-
-/* id for user defined functions */
-enum function_id {
- LSHIFT_LPAREN,
-};
-
-enum macro_id {
- HELLO,
- VOLUP,
- ALT_TAB,
-};
-
-
-/*
- * Fn action definition
- */
-#ifdef KEYMAP_SECTION_ENABLE
-const uint16_t fn_actions[] __attribute__ ((section (".keymap.fn_actions"))) = {
-#else
-const uint16_t fn_actions[] PROGMEM = {
-#endif
- [0] = ACTION_DEFAULT_LAYER_SET(0), // Default layer(not used)
- [1] = ACTION_LAYER_TAP_TOGGLE(1), // HHKB layer(toggle with 5 taps)
- [2] = ACTION_LAYER_TAP_KEY(2, KC_SLASH), // Cursor layer with Slash*
- [3] = ACTION_LAYER_TAP_KEY(3, KC_SCLN), // Mousekey layer with Semicolon*
- [4] = ACTION_LAYER_TAP_KEY(4, KC_SPC), // Mousekey layer with Space
- [5] = ACTION_LAYER_MOMENTARY(4), // Mousekey layer(IJKL)
- [6] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_ENT), // RControl with tap Enter
- [7] = ACTION_MODS_ONESHOT(MOD_LSFT), // Oneshot Shift
- [8] = ACTION_MACRO(ALT_TAB), // Application switching
- [9] = ACTION_MODS_KEY(MOD_LALT, KC_LEFT),
- [10] = ACTION_MODS_KEY(MOD_LALT, KC_RIGHT),
-
-// [x] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_BSPC), // LControl with tap Backspace
-// [x] = ACTION_LMOD_TAP_KEY(KC_LCTL, KC_ESC), // LControl with tap Esc
-// [x] = ACTION_FUNCTION_TAP(LSHIFT_LPAREN), // Function: LShift with tap '('
-// [x] = ACTION_MACRO(HELLO), // Macro: say hello
-// [x] = ACTION_MACRO(VOLUP), // Macro: media key
-};
-
-
-/*
- * Macro definition
- */
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
- switch (id) {
- case HELLO:
- return (record->event.pressed ?
- MACRO( I(0), T(H), T(E), T(L), T(L), W(255), T(O), END ) :
- MACRO_NONE );
- case VOLUP:
- return (record->event.pressed ?
- MACRO( D(VOLU), U(VOLU), END ) :
- MACRO_NONE );
- case ALT_TAB:
- return (record->event.pressed ?
- MACRO( D(LALT), D(TAB), END ) :
- MACRO( U(TAB), END ));
- }
- return MACRO_NONE;
-}
-
-
-
-/*
- * user defined action function
- */
-void action_function(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
- if (record->event.pressed) dprint("P"); else dprint("R");
- dprintf("%d", record->tap.count);
- if (record->tap.interrupted) dprint("i");
- dprint("\n");
-
- switch (id) {
- case LSHIFT_LPAREN:
- // Shift parentheses example: LShft + tap '('
- // http://stevelosh.com/blog/2012/10/a-modern-space-cadet/#shift-parentheses
- // http://geekhack.org/index.php?topic=41989.msg1304899#msg1304899
- if (record->event.pressed) {
- if (record->tap.count > 0 && !record->tap.interrupted) {
- if (record->tap.interrupted) {
- dprint("tap interrupted\n");
- register_mods(MOD_BIT(KC_LSHIFT));
- }
- } else {
- register_mods(MOD_BIT(KC_LSHIFT));
- }
- } else {
- if (record->tap.count > 0 && !(record->tap.interrupted)) {
- add_weak_mods(MOD_BIT(KC_LSHIFT));
- send_keyboard_report();
- register_code(KC_9);
- unregister_code(KC_9);
- del_weak_mods(MOD_BIT(KC_LSHIFT));
- send_keyboard_report();
- record->tap.count = 0; // ad hoc: cancel tap
- } else {
- unregister_mods(MOD_BIT(KC_LSHIFT));
- }
- }
- break;
- }
-}
+++ /dev/null
-/*
- * HHKB JP Layout
- */
-#include "keymap_common.h"
-
-
-#ifdef KEYMAP_SECTION_ENABLE
-const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] __attribute__ ((section (".keymap.keymaps"))) = {
-#else
-const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS] PROGMEM = {
-#endif
- /* Layer 0: Default Layer */
- KEYMAP_JP(ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, JYEN,BSPC, \
- TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, \
- LCTL,A, S, D, F, G, H, J, K, L, SCLN,QUOT,BSLS,ENT, \
- LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH,RO, UP, RSFT, \
- FN0, ZKHK,LGUI,LALT,MHEN, SPC, HENK,KANA,RALT,FN0, LEFT,DOWN,RGHT),
-
- /* Layer 1: HHKB mode (HHKB Fn)
- * ,-----------------------------------------------------------.
- * |Pwr| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
- * |-----------------------------------------------------------|
- * |Caps | | | | | | | |Psc|Slk|Pus|Up | | |
- * |------------------------------------------------------` |
- * | |VoD|VoU|Mut| | | *| /|Hom|PgU|Lef|Rig| | |
- * |-----------------------------------------------------------|
- * | | | | | | | +| -|End|PgD|Dow| | | |
- * |-----------------------------------------------------------|
- * | || | | | | | | | | || | | |
- * `-----------------------------------------------------------'
- */
- KEYMAP_JP(PWR, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \
- CAPS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,PSCR,SLCK,PAUS, UP, TRNS, \
- TRNS,VOLD,VOLU,MUTE,TRNS,TRNS,PAST,PSLS,HOME,PGUP,LEFT,RGHT,TRNS,PENT, \
- TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,PPLS,PMNS,END, PGDN,DOWN,TRNS,TRNS,TRNS, \
- TRNS,TRNS,TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS),
-};
-
-
-
-/*
- * Fn action definition
- */
-#ifdef KEYMAP_SECTION_ENABLE
-const uint16_t fn_actions[] __attribute__ ((section (".keymap.fn_actions"))) = {
-#else
-const uint16_t fn_actions[] PROGMEM = {
-#endif
- [0] = ACTION_LAYER_MOMENTARY(1),
-};
+++ /dev/null
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include <avr/io.h>
-#include "stdint.h"
-#include "led.h"
-
-
-/* HHKB has no LEDs */
-void led_set(uint8_t usb_led)
-{
- if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
- DDRD |= (1<<6);
- PORTD |= (1<<6);
- } else {
- DDRD |= (1<<6);
- PORTD &= ~(1<<6);
- }
-}
+++ /dev/null
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-/*
- * scan matrix
- */
-#include <stdint.h>
-#include <stdbool.h>
-#include <util/delay.h>
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "timer.h"
-#include "matrix.h"
-#include "hhkb_avr.h"
-#include <avr/wdt.h>
-#include "suspend.h"
-#include "lufa.h"
-
-
-// matrix power saving
-#define MATRIX_POWER_SAVE 10000
-static uint32_t matrix_last_modified = 0;
-
-// matrix state buffer(1:on, 0:off)
-static matrix_row_t *matrix;
-static matrix_row_t *matrix_prev;
-static matrix_row_t _matrix0[MATRIX_ROWS];
-static matrix_row_t _matrix1[MATRIX_ROWS];
-
-
-inline
-uint8_t matrix_rows(void)
-{
- return MATRIX_ROWS;
-}
-
-inline
-uint8_t matrix_cols(void)
-{
- return MATRIX_COLS;
-}
-
-void matrix_init(void)
-{
-#ifdef DEBUG
- debug_enable = true;
- debug_keyboard = true;
-#endif
-
- KEY_INIT();
-
- // initialize matrix state: all keys off
- for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix0[i] = 0x00;
- for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix1[i] = 0x00;
- matrix = _matrix0;
- matrix_prev = _matrix1;
-}
-
-uint8_t matrix_scan(void)
-{
- uint8_t *tmp;
-
- tmp = matrix_prev;
- matrix_prev = matrix;
- matrix = tmp;
-
- // power on
- if (!KEY_POWER_STATE()) KEY_POWER_ON();
- for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
- for (uint8_t col = 0; col < MATRIX_COLS; col++) {
- KEY_SELECT(row, col);
- _delay_us(5);
-
- // Not sure this is needed. This just emulates HHKB controller's behaviour.
- if (matrix_prev[row] & (1<<col)) {
- KEY_PREV_ON();
- }
- _delay_us(10);
-
- // NOTE: KEY_STATE is valid only in 20us after KEY_ENABLE.
- // If V-USB interrupts in this section we could lose 40us or so
- // and would read invalid value from KEY_STATE.
- uint8_t last = TIMER_RAW;
-
- KEY_ENABLE();
-
- // Wait for KEY_STATE outputs its value.
- // 1us was ok on one HHKB, but not worked on another.
- // no wait doesn't work on Teensy++ with pro(1us works)
- // no wait does work on tmk PCB(8MHz) with pro2
- // 1us wait does work on both of above
- // 1us wait doesn't work on tmk(16MHz)
- // 5us wait does work on tmk(16MHz)
- // 5us wait does work on tmk(16MHz/2)
- // 5us wait does work on tmk(8MHz)
- // 10us wait does work on Teensy++ with pro
- // 10us wait does work on 328p+iwrap with pro
- // 10us wait doesn't work on tmk PCB(8MHz) with pro2(very lagged scan)
- _delay_us(5);
-
- if (KEY_STATE()) {
- matrix[row] &= ~(1<<col);
- } else {
- matrix[row] |= (1<<col);
- }
-
- // Ignore if this code region execution time elapses more than 20us.
- // MEMO: 20[us] * (TIMER_RAW_FREQ / 1000000)[count per us]
- // MEMO: then change above using this rule: a/(b/c) = a*1/(b/c) = a*(c/b)
- if (TIMER_DIFF_RAW(TIMER_RAW, last) > 20/(1000000/TIMER_RAW_FREQ)) {
- matrix[row] = matrix_prev[row];
- }
-
- _delay_us(5);
- KEY_PREV_OFF();
- KEY_UNABLE();
-
- // NOTE: KEY_STATE keep its state in 20us after KEY_ENABLE.
- // This takes 25us or more to make sure KEY_STATE returns to idle state.
- _delay_us(75);
- }
- if (matrix[row] ^ matrix_prev[row]) matrix_last_modified = timer_read32();
- }
- // power off
- if (KEY_POWER_STATE() &&
- (USB_DeviceState == DEVICE_STATE_Suspended ||
- USB_DeviceState == DEVICE_STATE_Unattached ) &&
- timer_elapsed32(matrix_last_modified) > MATRIX_POWER_SAVE) {
- KEY_POWER_OFF();
- suspend_power_down();
- }
- return 1;
-}
-
-bool matrix_is_modified(void)
-{
- for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
- if (matrix[i] != matrix_prev[i])
- return true;
- }
- return false;
-}
-
-inline
-bool matrix_has_ghost(void)
-{
- return false;
-}
-
-inline
-bool matrix_is_on(uint8_t row, uint8_t col)
-{
- return (matrix[row] & (1<<col));
-}
-
-inline
-matrix_row_t matrix_get_row(uint8_t row)
-{
- return matrix[row];
-}
-
-void matrix_print(void)
-{
- print("\nr/c 01234567\n");
- for (uint8_t row = 0; row < matrix_rows(); row++) {
- xprintf("%02X: %08b\n", row, bitrev(matrix_get_row(row)));
- }
-}
-
-void matrix_power_up(void) {
- KEY_POWER_ON();
-}
-void matrix_power_down(void) {
- KEY_POWER_OFF();
-}
projects / max / tmk_keyboard.git / commitdiff