Add support of Model F 122 terminal keyboard

- change initialize of keyboard in matrix_scan()
- keymap for 122 keys
- Mafilefie and config.h for LUFA and PS/2 USART

diff --git a/converter/terminal_usb/Makefile b/converter/terminal_usb/Makefile
new file mode 100644 (file)
index 0000000..6154d86
--- /dev/null
+++ b/converter/terminal_usb/Makefile
@@ -0,0 +1,113 @@
+# Target file name (without extension).
+TARGET = terminal_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =  keymap.c \
+       matrix.c \
+       led.c
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes        # Virtual DIP switch configuration(+1000)
+#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes   # Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes     # USB Nkey Rollover - not yet supported in LUFA
+
+
+#
+# PS/2 protocol implementations
+#      USART is recommended if it is available, others are for reference purpose.
+#      INT implementation will drop simultaneous key strokes.
+#
+PS2_USE_USART = yes    # uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_INT = yes     # uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes        # uses primitive reference code
+
+ifdef PS2_USE_USART
+    SRC += protocol/ps2_usart.c
+    OPT_DEFS += -DPS2_USE_USART
+endif
+
+ifdef PS2_USE_INT
+    SRC += protocol/ps2.c
+    OPT_DEFS += -DPS2_USE_INT
+endif
+
+ifdef PS2_USE_BUSYWAIT
+    SRC += protocol/ps2.c
+    OPT_DEFS += -DPS2_USE_BUSYWAIT
+endif
+
+
+#---------------- Programming Options --------------------------
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk

diff --git a/converter/terminal_usb/Makefile.102_pjrc b/converter/terminal_usb/Makefile.102_pjrc
deleted file mode 100644 (file)
index e2d1a00..0000000
--- a/converter/terminal_usb/Makefile.102_pjrc
+++ /dev/null
@@ -1,61 +0,0 @@
-#
-# Makefile for PJRC Teensy
-#
-
-
-# Target file name (without extension).
-TARGET = terminal_usb_102_pjrc
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =  keymap_102.c \
-       matrix.c \
-       led.c \
-       ps2.c
-
-CONFIG_H = config_102_pjrc.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Build Options
-#   *Comment out* to disable the options.
-#
-MOUSEKEY_ENABLE = yes  # Mouse keys
-EXTRAKEY_ENABLE = yes  # Audio control and System control
-NKRO_ENABLE = yes      # USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk

diff --git a/converter/terminal_usb/Makefile.122_pjrc b/converter/terminal_usb/Makefile.122_pjrc
deleted file mode 100644 (file)
index ee42dd7..0000000
--- a/converter/terminal_usb/Makefile.122_pjrc
+++ /dev/null
@@ -1,61 +0,0 @@
-#
-# Makefile for PJRC Teensy
-#
-
-
-# Target file name (without extension).
-TARGET = terminal_usb_122_pjrc
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =  keymap_122.c \
-       matrix.c \
-       led.c \
-       ps2.c
-
-CONFIG_H = config_122_pjrc.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Build Options
-#   *Comment out* to disable the options.
-#
-#MOUSEKEY_ENABLE = yes # Mouse keys
-#EXTRAKEY_ENABLE = yes # Audio control and System control
-#NKRO_ENABLE = yes     # USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk

diff --git a/converter/terminal_usb/config.h b/converter/terminal_usb/config.h
new file mode 100644 (file)
index 0000000..ea5ce62
--- /dev/null
+++ b/converter/terminal_usb/config.h
@@ -0,0 +1,138 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6535
+#define DEVICE_VER      0x0100
+#define MANUFACTURER    t.m.k.
+#define PRODUCT         PS/2(Set3)-USB Keyboard converter(IBM 122keys)
+#define DESCRIPTION     USB converter for IBM Terminal Keyboard 122keys
+
+
+/* matrix size */
+#define MATRIX_ROWS 17  // keycode bit: 3-0
+#define MATRIX_COLS 8   // keycode bit: 6-4
+
+
+/* legacy keymap support */
+#define USE_LEGACY_KEYMAP
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) || \
+    (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL)))  \
+)
+
+
+/* 
+ * PS/2 USART configuration for ATMega32U4
+ */
+#ifdef PS2_USE_USART
+/* XCK for clock line */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   5
+/* RXD for data line */
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    2
+
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do {   \
+    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
+    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
+    UCSR1C = ((1 << UMSEL10) |  \
+              (3 << UPM10)   |  \
+              (0 << USBS1)   |  \
+              (3 << UCSZ10)  |  \
+              (0 << UCPOL1));   \
+    UCSR1A = 0;                 \
+    UBRR1H = 0;                 \
+    UBRR1L = 0;                 \
+} while (0)
+#define PS2_USART_RX_INT_ON() do {  \
+    UCSR1B = ((1 << RXCIE1) |       \
+              (1 << RXEN1));        \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+    UCSR1B = (1 << RXEN1);          \
+} while (0)
+#define PS2_USART_OFF() do {    \
+    UCSR1C = 0;                 \
+    UCSR1B &= ~((1 << RXEN1) |  \
+                (1 << TXEN1));  \
+} while (0)
+#define PS2_USART_RX_READY      (UCSR1A & (1<<RXC1))
+#define PS2_USART_RX_DATA       UDR1
+#define PS2_USART_ERROR         (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
+#define PS2_USART_RX_VECT       USART1_RX_vect
+#endif
+
+
+/*
+ * PS/2 Interrupt configuration
+ */
+#ifdef PS2_USE_INT
+/* uses INT1 for clock line(ATMega32U4) */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   1
+
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    0
+
+#define PS2_INT_INIT()  do {    \
+    EICRA |= ((1<<ISC11) |      \
+              (0<<ISC10));      \
+} while (0)
+#define PS2_INT_ON()  do {      \
+    EIMSK |= (1<<INT1);         \
+} while (0)
+#define PS2_INT_OFF() do {      \
+    EIMSK &= ~(1<<INT1);        \
+} while (0)
+#define PS2_INT_VECT    INT1_vect
+#endif
+
+
+/*
+ * PS/2 Busywait configuration
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   1
+
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    0
+#endif
+
+#endif

diff --git a/converter/terminal_usb/config_102_pjrc.h b/converter/terminal_usb/config_102_pjrc.h
deleted file mode 100644 (file)
index 65001a7..0000000
--- a/converter/terminal_usb/config_102_pjrc.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6531
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         PS/2(Set3)-USB Keyboard converter(IBM 102keys)
-#define DESCRIPTION     USB converter for IBM Terminal Keyboard 102keys
-
-
-/* matrix size */
-#define MATRIX_ROWS 17  // keycode bit: 3-0
-#define MATRIX_COLS 8   // keycode bit: 6-4
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL))  \
-)
-
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 255
-#endif
-
-
-/* PS/2 lines */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-
-#endif

diff --git a/converter/terminal_usb/config_122_pjrc.h b/converter/terminal_usb/config_122_pjrc.h
deleted file mode 100644 (file)
index 90e5edd..0000000
--- a/converter/terminal_usb/config_122_pjrc.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6532
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         PS/2(Set3)-USB Keyboard converter(IBM 122keys)
-#define DESCRIPTION     USB converter for IBM Terminal Keyboard 122keys
-
-
-/* matrix size */
-#define MATRIX_ROWS 17  // keycode bit: 3-0
-#define MATRIX_COLS 8   // keycode bit: 6-4
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL))  \
-)
-
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 255
-#endif
-
-
-/* PS/2 lines */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-
-#endif

diff --git a/converter/terminal_usb/keymap_122.c b/converter/terminal_usb/keymap.c
similarity index 88%
rename from converter/terminal_usb/keymap_122.c
rename to converter/terminal_usb/keymap.c
index 79ca11c26fe2e19b669e208b895d49b28a2df986..73009cb47e8f87f7137203d5d3987316cae2e22e 100644 (file)
--- a/converter/terminal_usb/keymap_122.c
+++ b/converter/terminal_usb/keymap.c
@@ -28,7 +28,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 
 /* 
- * IBM Terminal keyboard 1392595(102keys)
+ * IBM Terminal keyboard 6110345(122keys)/1392595(102keys)
  * http://geekhack.org/showthread.php?10737-What-Can-I-Do-With-a-Terminal-Model-M
  * http://www.seasip.info/VintagePC/ibm_1391406.html
  *
@@ -114,6 +114,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
      * |Ctrl|    |Alt |          Space              |Alt |    |Ctrl| |Lef|Dow|Rig| |      0|  .|   |
      * `----'    `---------------------------------------'    `----' `-----------' `---------------'
      */
+/*
     KEYMAP(
                      F13, F14, F15, F16, F17, F18, F19, F20, F21, F22, F23, F24,
                      F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,
@@ -124,6 +125,18 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     APP, INT6,  LSFT,NUBS,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, SLSH,     RO,  RSFT,  LEFT,INT2,RGHT,  P1,  P2,  P3,  PENT,
     RGUI,LGUI,  LCTL,     LALT,               SPC,                          RALT,     RCTL,       DOWN,       NO,  P0,  PDOT,NO
     ),
+*/
+    // pseudo ANSI
+    KEYMAP(
+                     F13, F14, F15, F16, F17, F18, F19, F20, F21, F22, F23, F24,
+                     F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,
+
+    PSCR,ESC,   ESC, 1,   2,   3,   4,   5,   6,   7,   8,   9,   0,   MINS,EQL, NO,  BSPC,  INS, HOME,PGUP,  NLCK,PSLS,PAST,PMNS,
+    SLCK,INT4,  TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,     NO,    DEL, END, PGDN,  P7,  P8,  P9,  PPLS,
+    PAUS,INT5,  LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   SCLN,QUOT,     BSLS,ENT,        UP,         P4,  P5,  P6,  PCMM,
+    APP, INT6,  LSFT,LSFT,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, SLSH,     NO,  RSFT,  LEFT,INT2,RGHT,  P1,  P2,  P3,  PENT,
+    RGUI,LGUI,  LCTL,     LALT,               SPC,                          LGUI,     GRV,        DOWN,       NO,  P0,  PDOT,NO
+    ),
 };
 
 

diff --git a/converter/terminal_usb/keymap_102.c b/converter/terminal_usb/keymap_102.c
deleted file mode 100644 (file)
index e9412b2..0000000
--- a/converter/terminal_usb/keymap_102.c
+++ /dev/null
@@ -1,208 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/pgmspace.h>
-#include "keycode.h"
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "keymap.h"
-
-
-
-
-/* 
- * IBM Terminal keyboard 1392595(102keys)
- * http://geekhack.org/showthread.php?10737-What-Can-I-Do-With-a-Terminal-Model-M
- * http://www.seasip.info/VintagePC/ibm_1391406.html
- *
- * Keymap array:
- *     8 bytes
- *   +---------+
- *  0|         |
- *  :|         | 0x00-0x87
- *  ;|         |
- * 17|         |
- *   +---------+
- */
-#define KEYMAP( \
-    K08,    K07,K0F,K17,K1F,K27,K2F,K37,K3F,K47,K4F,K56,K5E,      K57,K5F,K62,                   \
-                                                                                                 \
-    K0E,K16,K1E,K26,K25,K2E,K36,K3D,K3E,K46,K45,K4E,K55,K5D,K66,  K67,K6E,K6F,  K76,K77,K7E,K84, \
-    K0D,K15,K1D,K24,K2D,K2C,K35,K3C,K43,K44,K4D,K54,K5B,    K5C,  K64,K65,K6D,  K6C,K75,K7D,K7C, \
-    K14,K1C,K1B,K23,K2B,K34,K33,K3B,K42,K4B,K4C,K52,    K53,K5A,                K6B,K73,K74,K7B, \
-    K12,K13,K1A,K22,K21,K2A,K32,K31,K3A,K41,K49,K4A,    K51,K59,      K63,      K69,K72,K7A,K79, \
-    K11,    K19,            K29,                    K39,    K58,  K61,K60,K6A,  K68,K70,K71,K78  \
-) { \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_##K07 }, \
-    { KC_##K08, KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_##K0D, KC_##K0E, KC_##K0F }, \
-    { KC_NO,    KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
-    { KC_NO,    KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
-    { KC_NO,    KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
-    { KC_NO,    KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
-    { KC_NO,    KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
-    { KC_NO,    KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_##K3F }, \
-    { KC_NO,    KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_##K45, KC_##K46, KC_##K47 }, \
-    { KC_NO,    KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D, KC_##K4E, KC_##K4F }, \
-    { KC_NO,    KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
-    { KC_##K58, KC_##K59, KC_##K5A, KC_##K5B, KC_##K5C, KC_##K5D, KC_##K5E, KC_##K5F }, \
-    { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_##K67 }, \
-    { KC_##K68, KC_##K69, KC_##K6A, KC_##K6B, KC_##K6C, KC_##K6D, KC_##K6E, KC_##K6F }, \
-    { KC_##K70, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
-    { KC_##K78, KC_##K79, KC_##K7A, KC_##K7B, KC_##K7C, KC_##K7D, KC_##K7E, KC_NO    }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_##K84, KC_NO,    KC_NO,    KC_NO,   }, \
-}
-
-
-// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
-static const uint8_t PROGMEM fn_layer[] = {
-    1,              // Fn0
-    2,              // Fn1
-    3,              // Fn2
-    0,              // Fn3
-    0,              // Fn4
-    0,              // Fn5
-    0,              // Fn6
-    0               // Fn7
-};
-
-// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
-// See layer.c for details.
-static const uint8_t PROGMEM fn_keycode[] = {
-    KC_SCLN,        // Fn0
-    KC_SLSH,        // Fn1
-    KC_ESC,         // Fn2
-    KC_NO,          // Fn3
-    KC_NO,          // Fn4
-    KC_NO,          // Fn5
-    KC_NO,          // Fn6
-    KC_NO           // Fn7
-};
-
-
-static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /* 0: default
-     * ,---.   ,---------------. ,---------------. ,---------------. ,-----------.
-     * |Esc|   |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau|
-     * `---'   `---------------' `---------------' `---------------' `-----------'
-     * ,-----------------------------------------------------------. ,-----------. ,---------------.
-     * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|  \|BS | |Ins|Hom|PgU| |NmL|  /|  *|  -|
-     * |-----------------------------------------------------------| |-----------| |---------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \| |Del|End|PgD| |  7|  8|  9|   |
-     * |-----------------------------------------------------------| `-----------' |-----------|  +|
-     * |CapsLo|  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|  #|Retu|               |  4|  5|  6|   |
-     * |-----------------------------------------------------------|     ,---.     |---------------|
-     * |Shif|  \|  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|Shift     |     |Up |     |  1|  2|  3|   |
-     * |-----------------------------------------------------------| ,-----------. |-----------|Ent|
-     * |Ctrl|    |Alt |          Space              |Alt |    |Ctrl| |Lef|Dow|Rig| |      0|  .|   |
-     * `----'    `---------------------------------------'    `----' `-----------' `---------------'
-     */
-    KEYMAP(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,             PSCR,SLCK,BRK,
-    GRV, 1,   2,   3,   4,   5,   6,   7,   8,   9,   0,   MINS,EQL, JYEN,BSPC,  INS, HOME,PGUP,  NLCK,PSLS,PAST,PMNS,
-    TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,     BSLS,  DEL, END, PGDN,  P7,  P8,  P9,  PPLS,
-    LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   FN0, QUOT,     NUHS,ENT,                    P4,  P5,  P6,  PCMM,
-    LSFT,NUBS,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, FN1,      RO,  FN2,        UP,         P1,  P2,  P3,  PENT,
-    LGUI,     LALT,               SPC,                          RALT,     RCTL,  LEFT,DOWN,RGHT,  NO,  P0,  PDOT,NO
-    ),
-
-    /* 1: Mouse keys
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backspa|
-     * |-----------------------------------------------------------|
-     * |Tab  |MwL|MwU|McU|WwU|WwR|MwL|MwD|MwU|MwR|   |   |   |    \|
-     * |-----------------------------------------------------------|
-     * |CapsLo|   |McL|McD|McR|   |McL|McD|McU|McR|Fn0|   |Return  |
-     * |-----------------------------------------------------------|
-     * |Shift   |VoD|VoU|Mut|Mb2|Mb3|Mb2|Mb1|VoD|VoU|Mut|Shift     |
-     * |-----------------------------------------------------------|
-     * |Ctrl |    |Alt |         Mb1                |Alt |    |Ctrl|
-     * `-----'    `--------------------------------------'    `----'
-     * Mc = mouse cursor, Mw = mouse wheel, Mb = mouse button
-     * Vo = Volume, Mut = Mute
-     */
-    KEYMAP(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,                PSCR,SLCK,BRK,
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F8,  F10, F11, F12, NO,  BSPC,     INS, HOME,PGUP,    NLCK,PSLS,PAST,PMNS,
-    TAB, WH_L,WH_D,MS_U,WH_U,WH_R,WH_L,WH_D,WH_U,WH_R,NO,  NO,  NO,       BSLS,     DEL, END, PGDN,    P7,  P8,  P9,  PPLS,
-    LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN0, NO,       NO,  ENT,                         P4,  P5,  P6,  PCMM,
-    LSFT,NO,  VOLD,VOLU,MUTE,BTN2,BTN3,BTN2,BTN1,VOLD,VOLU,MUTE,     NO,  RSFT,          UP,           P1,  P2,  P3,  PENT,
-    LGUI,     LALT,               BTN1,                         RALT,     RCTL,     LEFT,DOWN,RGHT,    NO,  P0,  PDOT,NO
-    ),
-
-    /* 2: Cursor keys
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backspa|
-     * |-----------------------------------------------------------|
-     * |Tab  |Hom|PgU| Up|PgU|End|Hom|PgD|PgU|End|   |   |   |    \|
-     * |-----------------------------------------------------------|
-     * |CapsLo|   |Lef|Dow|Rig|   |Lef|Dow| Up|Rig|   |   |Return  |
-     * |-----------------------------------------------------------|
-     * |Shift   |   |   |   |   |   |Hom|PgD|PgU|End|Fn1|Shift     |
-     * |-----------------------------------------------------------|
-     * |Ctrl |    |Alt |         Space              |Alt |    |Ctrl|
-     * `-----'    `--------------------------------------'    `----'
-     */
-    KEYMAP(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,                PSCR,SLCK,BRK,
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F8,  F10, F11, F12, NO,  BSPC,     INS, HOME,PGUP,    NLCK,PSLS,PAST,PMNS,
-    TAB, NO,  NO,  NO,  NO,  NO,  HOME,PGDN,PGUP,END, NO,  NO,  NO,       BSLS,     DEL, END, PGDN,    P7,  P8,  P9,  PMNS,
-    LCTL,NO,  NO,  NO,  NO,  NO,  LEFT,DOWN,UP,  RGHT,NO,  NO,       NO,  ENT,                         P4,  P5,  P6,  PCMM,
-    LSFT,NO,  VOLD,VOLU,MUTE,NO,  NO,  HOME,PGDN,PGUP,END, FN1,      NO,  RSFT,          UP,           P1,  P2,  P3,  PENT,
-    LGUI,     LALT,               SPC,                          RALT,     RCTL,     LEFT,DOWN,RGHT,    NO,  P0,  PDOT,NO
-    ),
-
-    /* 3: HHKB
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
-     * |-----------------------------------------------------------|
-     * |Caps |   |   |   |   |   |   |   |Psc|Slk|Pus|Up |   |Backs|
-     * |-----------------------------------------------------------|
-     * |Contro|VoD|VoU|Mut|   |   |  *|  /|Hom|PgU|Lef|Rig|Enter   |
-     * |-----------------------------------------------------------|
-     * |Shift   |   |   |   |   |   |  +|  -|End|PgD|Dow|Fn2       |
-     * |-----------------------------------------------------------|
-     * |Ctrl |    |Alt |         Space              |Alt |    |Ctrl|
-     * `-----'    `--------------------------------------'    `----'
-     */
-    KEYMAP(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12,                PSCR,SLCK,BRK,
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F8,  F10, F11, F12, NO,  BSPC,     INS, HOME,PGUP,    NLCK,PSLS,PAST,PMNS,
-    CAPS,NO,  NO,  NO,  NO,  NO,  NO,  NO,  PSCR,SLCK,BRK, UP,  NO,       BSLS,     DEL, END, PGDN,    P7,  P8,  P9,  PPLS,
-    LCTL,VOLD,VOLU,MUTE,NO,  NO,  PAST,PSLS,HOME,PGUP,LEFT,RGHT,     NO,  ENT,                         P4,  P5,  P6,  PCMM,
-    LSFT,NO,  NO,  NO,  NO,  NO,  NO,  PPLS,PMNS,END, PGDN,DOWN,     NO,  FN2,           UP,           P1,  P2,  P3,  PENT,
-    LGUI,     LALT,               SPC,                          RALT,     RCTL,     LEFT,DOWN,RGHT,    NO,  P0,  PDOT,NO
-    ),
-};
-
-
-uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
-{
-    return pgm_read_byte(&keymaps[(layer)][(row)][(col)]);
-}
-
-uint8_t keymap_fn_layer(uint8_t index)
-{
-    return pgm_read_byte(&fn_layer[index]);
-}
-
-uint8_t keymap_fn_keycode(uint8_t index)
-{
-    return pgm_read_byte(&fn_keycode[index]);
-}

diff --git a/converter/terminal_usb/matrix.c b/converter/terminal_usb/matrix.c
index a6eff8c1ece026fb3dcd71e7a3bcd87dfe090e54..36901536f14e512a3d40b79f031979fa46664d66 100644 (file)
--- a/converter/terminal_usb/matrix.c
+++ b/converter/terminal_usb/matrix.c
@@ -66,20 +66,12 @@ uint8_t matrix_cols(void)
 
 void matrix_init(void)
 {
-    print_enable = true;
     debug_enable = true;
     //debug_matrix = true;
     //debug_keyboard = true;
     //debug_mouse = false;
 
     ps2_host_init();
-    // Make and Break code without Typematic
-    while (ps2_host_send(0xF8) != 0xFA) {
-        debug("send F8: failed\n");
-        _delay_ms(500);
-    }
-    debug("send F8: OK\n");
-
 
     // initialize matrix state: all keys off
     for (uint8_t i=0; i < MATRIX_ROWS; i++) matrix[i] = 0x00;
@@ -92,46 +84,90 @@ uint8_t matrix_scan(void)
 
     // scan code reading states
     static enum {
-        INIT,
+        RESET,
+        RESET_RESPONSE,
+        KBD_ID0,
+        KBD_ID1,
+        CONFIG,
+        READY,
         F0,
-    } state = INIT;
-
+    } state = RESET;
 
     is_modified = false;
 
     uint8_t code;
-    while ((code = ps2_host_recv())) {
-        debug_hex(code);
-        switch (state) {
-            case INIT:
-                switch (code) {
-                    case 0xF0:
-                        state = F0;
-                        debug(" ");
-                        break;
-                    default:    // normal key make
-                        if (code < 0x88) {
-                            matrix_make(code);
-                        } else {
-                            debug("unexpected scan code at INIT: "); debug_hex(code); debug("\n");
-                        }
-                        state = INIT;
-                        debug("\n");
-                }
-                break;
-            case F0:    // Break code
-                switch (code) {
-                    default:
+    if ((code = ps2_host_recv())) {
+        debug("r"); debug_hex(code); debug(" ");
+    }
+
+    switch (state) {
+        case RESET:
+            debug("wFF ");
+            if (ps2_host_send(0xFF) == 0xFA) {
+                debug("[ack]\nRESET_RESPONSE: ");
+                state = RESET_RESPONSE;
+            }
+            break;
+        case RESET_RESPONSE:
+            if (code == 0xAA) {
+                debug("[ok]\nKBD_ID: ");
+                state = KBD_ID0;
+            } else if (code) {
+                debug("err\nRESET: ");
+                state = RESET;
+            }
+            break;
+        // after reset receive keyboad ID(2 bytes)
+        case KBD_ID0:
+            if (code) {
+                state = KBD_ID1;
+            }
+            break;
+        case KBD_ID1:
+            if (code) {
+                debug("\nCONFIG: ");
+                state = CONFIG;
+            }
+            break;
+        case CONFIG:
+            debug("wF8 ");
+            if (ps2_host_send(0xF8) == 0xFA) {
+                debug("[ack]\nREADY\n");
+                state = READY;
+            }
+            break;
+        case READY:
+            switch (code) {
+                case 0x00:
+                    break;
+                case 0xF0:
+                    state = F0;
+                    debug(" ");
+                    break;
+                default:    // normal key make
+                    if (code < 0x88) {
+                        matrix_make(code);
+                    } else {
+                        debug("unexpected scan code at READY: "); debug_hex(code); debug("\n");
+                    }
+                    state = READY;
+                    debug("\n");
+            }
+            break;
+        case F0:    // Break code
+            switch (code) {
+                case 0x00:
+                    break;
+                default:
                     if (code < 0x88) {
                         matrix_break(code);
                     } else {
                         debug("unexpected scan code at F0: "); debug_hex(code); debug("\n");
                     }
-                    state = INIT;
+                    state = READY;
                     debug("\n");
-                }
-                break;
-        }
+            }
+            break;
     }
     return 1;
 }