Add new build options to adb_usb

diff --git a/converter/adb_usb/Makefile b/converter/adb_usb/Makefile
index 87b0f415b8ed401bc3f1dd569a6545be8d45d14c..09f30180a83d7124c4bbcd0bc1b4bd84abdb841e 100644 (file)
--- a/converter/adb_usb/Makefile
+++ b/converter/adb_usb/Makefile
@@ -32,12 +32,25 @@ MCU = atmega32u4       # Teensy 2.0
 F_CPU = 16000000
 
 
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
 # Build Options
 #   comment out to disable the options.
 #
-#MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes  # Audio control and System control
-#NKRO_ENABLE = yes     # USB Nkey Rollover
+#BOOTMAGIC_ENABLE = yes        # Virtual DIP switch configuration(+1000)
+#MOUSEKEY_ENABLE = yes # Mouse keys(+5000)
+#EXTRAKEY_ENABLE = yes # Audio control and System control(+600)
+#CONSOLE_ENABLE = yes    # Console for debug
+#COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes     # USB Nkey Rollover(+500)
 
 
 # Search Path

diff --git a/converter/adb_usb/Makefile.lufa b/converter/adb_usb/Makefile.lufa
new file mode 100644 (file)
index 0000000..372ef6c
--- /dev/null
+++ b/converter/adb_usb/Makefile.lufa
@@ -0,0 +1,131 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = adb_usb_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =  keymap.c \
+       matrix.c \
+       led.c \
+       adb.c
+
+CONFIG_H = config.h
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
+CONSOLE_ENABLE = yes   # Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes     # USB Nkey Rollover - not yet supported in LUFA
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk

diff --git a/converter/adb_usb/keymap.c b/converter/adb_usb/keymap.c
index 5d42980d5540dae261e8584b5cbb072f4bb20400..a1574b1ab3cbc769a5f3a2be7eb9dddc109e1d27 100644 (file)
--- a/converter/adb_usb/keymap.c
+++ b/converter/adb_usb/keymap.c
@@ -21,7 +21,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #include <stdint.h>
 #include <stdbool.h>
 #include <avr/pgmspace.h>
-#include "usb_keyboard.h"
 #include "keycode.h"
 #include "print.h"
 #include "debug.h"

diff --git a/converter/adb_usb/matrix.c b/converter/adb_usb/matrix.c
index 9b26a2a18762955762017d4fb60dcbdddbbf41df..a616d10e40c176fb69e05af205bbc9bec605f8c6 100644 (file)
--- a/converter/adb_usb/matrix.c
+++ b/converter/adb_usb/matrix.c
@@ -71,7 +71,6 @@ void matrix_init(void)
     // initialize matrix state: all keys off
     for (uint8_t i=0; i < MATRIX_ROWS; i++) matrix[i] = 0x00;
 
-    print_enable = true;
     debug_enable = true;
     debug_matrix = true;
     debug_keyboard = true;

diff --git a/protocol/pjrc/usb.c b/protocol/pjrc/usb.c
index a9fbc4638efbedb8a07ee14c512343f090891df3..14df9efdda88d6460925baeb775182deeb3a6c08 100644 (file)
--- a/protocol/pjrc/usb.c
+++ b/protocol/pjrc/usb.c
@@ -31,6 +31,7 @@
 #include "usb_mouse.h"
 #include "usb_debug.h"
 #include "usb_extra.h"
+#include "led.h"
 #include "print.h"
 #include "util.h"
 #include "sleep_led.h"