added HHKB/README and clean some codes.

diff --git a/adb.c b/adb.c
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/adb_usb/Makefile b/adb_usb/Makefile
old mode 100755 (executable)
new mode 100644 (file)
index 92b9ba1..802b424
--- a/adb_usb/Makefile
+++ b/adb_usb/Makefile
@@ -38,7 +38,7 @@ F_CPU = 16000000
 #
 MOUSEKEY_ENABLE = yes  # Mouse keys
 #PS2_MOUSE_ENABLE = yes        # PS/2 mouse(TrackPoint) support
-USB_EXTRA_ENABLE = yes # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 #USB_NKRO_ENABLE = yes # USB Nkey Rollover
 
 

diff --git a/adb_usb/matrix.c b/adb_usb/matrix.c
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/command.c b/command.c
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/Makefile b/hhkb/Makefile
old mode 100755 (executable)
new mode 100644 (file)
index 4a0af1c..e1cc2f2
--- a/hhkb/Makefile
+++ b/hhkb/Makefile
@@ -1,5 +1,10 @@
+#
+# Makefile for PJRC Teensy
+#
+
+
 # Target file name (without extension).
-TARGET = hhkb
+TARGET = hhkb_pjrc
 
 # Directory common source filess exist
 COMMON_DIR = ..
@@ -13,7 +18,7 @@ TARGET_SRC =  main_pjrc.c \
                matrix.c \
                led.c
 
-CONFIG_H = config.h
+CONFIG_H = config_pjrc.h
 
 
 # MCU name, you MUST set this to match the board you are using
@@ -36,7 +41,7 @@ F_CPU = 16000000
 #   comment out to disable the options.
 MOUSEKEY_ENABLE = yes  # Mouse keys
 #PS2_MOUSE_ENABLE = yes        # PS/2 mouse(TrackPoint) support
-USB_EXTRA_ENABLE = yes # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 USB_NKRO_ENABLE = yes  # USB Nkey Rollover
 
 

diff --git a/hhkb/Makefile.vusb b/hhkb/Makefile.vusb
index 7826ffd02574c8c459c831953ab9e3c5975521ca..77841b824cb97e0a3aacbcf43848899aef028fde 100644 (file)
--- a/hhkb/Makefile.vusb
+++ b/hhkb/Makefile.vusb
@@ -1,3 +1,8 @@
+#
+# Makefile for V-USB
+#
+
+
 # Target file name (without extension).
 TARGET = hhkb_vusb
 
@@ -23,10 +28,6 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 
 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-#MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
 MCU = atmega168
 
 
@@ -42,7 +43,7 @@ F_CPU = 20000000
 #   comment out to disable the options.
 #
 MOUSEKEY_ENABLE = yes  # Mouse keys
-USB_EXTRA_ENABLE = yes # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 #USB_NKRO_ENABLE = yes # USB Nkey Rollover
 
 

diff --git a/hhkb/README b/hhkb/README
new file mode 100644 (file)
index 0000000..2a44181
--- /dev/null
+++ b/hhkb/README
@@ -0,0 +1,80 @@
+Alternative Controller for HHKB
+===============================
+
+Feature
+-------
+- Mouse Keys
+- NKRO on USB
+- Keymap Layers
+
+
+Customize Keymap
+----------------
+see keymap.c.
+
+
+Build for Teensy
+----------------
+0. Edit matrix.c.
+    adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
+1. Define macros in config_pjrc.h.(Optional)
+    VENDOR_ID, PRODUCT_ID and string descriptor.
+    IS_COMMAND
+2. Edit Makefile for MCU setting and build options.
+    MCU, F_CPU
+    MOUSEKEY_ENABLE, USB_EXTRA_ENABLE, USB_NKRO_ENABLE
+3. Build hex file.
+    $ make
+4. Program MCU.
+    $  make program
+
+
+Build for V-USB
+---------------
+0. Edit matrix.c and usbconfig.h.
+    adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
+    define macros for V-USB in usbconfig.h.
+1. Define macros in config_vusb.h.(Optional)
+    IS_COMMAND
+2. Edit Makefile.vusb for MCU setting and build options.
+    MCU, F_CPU
+    MOUSEKEY_ENABLE, USB_EXTRA_ENABLE, USB_NKRO_ENABLE
+3. Build hex file.
+    $ make -f Makefile.vusb
+4. Program MCU.
+    $  make -f Makefile.vusb program
+
+    Using a bootloader to program for convenience is recommended.
+    Once program this V-USB bootloader at first, you can program MCU without
+    extra programmer. You should have reset switch to start up as bootloader
+    mode in this case.
+    USBaspLoader:
+    http://www.obdev.at/products/vusb/usbasploader.html
+
+
+V-USB Circuit
+-------------
+                +---+   +---------------+
+USB            GND  |   |   ATmega168   |
+===                 C3  |               |
+5V <-------+--------+---|Vcc,AVCC       |        HHKB
+           R1           |               |        ====
+D- <----+--+-----R2-----|INT1      PB0-2|------->ROW
+D+ <----|---+----R3-----|INT0      PB3-5|------->COL
+        Z1  Z2          |            PB6|------->ENABLE
+GND<----+---+--+--+-----|GND         PE6|------->KEY
+               |  |     |            PE7|------->PREV
+               |  C2-+--|XTAL1          |        (see doc/HHKB.txt for pinouts)
+               |     X1 |               |
+               +--C3-+--|XTAL2       RST|---SW--+GND
+                        +---------------+
+R1:     1.5K Ohm
+R2,R3:  68 Ohm
+Z1,Z2:  Zener 3.6V
+C1,C2:  22pF
+C3:     0.1uF
+X1:     Crystal 20MHz(16MHz/12MHz)
+SW:     Push Switch(Optional for bootloader)
+
+
+EOF

diff --git a/hhkb/config.h b/hhkb/config_pjrc.h
similarity index 100%
rename from hhkb/config.h
rename to hhkb/config_pjrc.h

diff --git a/hhkb/config_vusb.h b/hhkb/config_vusb.h
index 3b44b94a310a0eac71f54dcd83167032f88c8f84..7c4291a2139fa87411eba259634f7a3d666de094 100644 (file)
--- a/hhkb/config_vusb.h
+++ b/hhkb/config_vusb.h
@@ -29,92 +29,4 @@
 #endif
 
 
-/* PS/2 lines */
-#ifdef PS2_MOUSE_ENABLE
-
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   4
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-
-
-// Synchronous USART is used to receive data from keyboard.
-// Use RXD pin for PS/2 DATA line and XCK for PS/2 CLOCK.
-// NOTE: This is recomended strongly if you use V-USB library.
-#define PS2_USE_USART
-
-// External or Pin Change Interrupt is used to receive data from keyboard.
-// Use INT1 or PCINTxx for PS/2 CLOCK line. see below.
-//#define PS2_USE_INT
-
-
-#ifdef PS2_USE_USART
-// synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge
-// set DDR of CLOCK as input to be slave
-#define PS2_USART_INIT() do {   \
-    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
-    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
-    UCSR0C = ((1 << UMSEL00) |  \
-              (3 << UPM00)   |  \
-              (0 << USBS0)   |  \
-              (3 << UCSZ00)  |  \
-              (0 << UCPOL0));   \
-    UCSR0A = 0;                 \
-    UBRR0H = 0;                 \
-    UBRR0L = 0;                 \
-} while (0)
-#define PS2_USART_RX_INT_ON() do {  \
-    UCSR0B = ((1 << RXCIE0) |       \
-              (1 << RXEN0));        \
-} while (0)
-#define PS2_USART_RX_POLL_ON() do { \
-    UCSR0B = (1 << RXEN0);          \
-} while (0)
-#define PS2_USART_OFF() do {    \
-    UCSR0C = 0;                 \
-    UCSR0B &= ~((1 << RXEN0) |  \
-                (1 << TXEN0));  \
-} while (0)
-#define PS2_USART_RX_READY      (UCSR0A & (1<<RXC0))
-#define PS2_USART_RX_DATA       UDR0
-#define PS2_USART_ERROR         (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0)))
-#define PS2_USART_RX_VECT       USART_RX_vect
-#endif
-
-
-#ifdef PS2_USE_INT
-/* INT1
-#define PS2_INT_INIT()  do {    \
-    EICRA |= ((1<<ISC11) |      \
-              (0<<ISC10));      \
-} while (0)
-#define PS2_INT_ON()  do {      \
-    EIMSK |= (1<<INT1);         \
-} while (0)
-#define PS2_INT_OFF() do {      \
-    EIMSK &= ~(1<<INT1);        \
-} while (0)
-#define PS2_INT_VECT    INT1_vect
-*/
-
-/* PCINT20 */
-#define PS2_INT_INIT()  do {    \
-    PCICR  |= (1<<PCIE2);       \
-} while (0)
-#define PS2_INT_ON()  do {      \
-    PCMSK2 |= (1<<PCINT20);     \
-} while (0)
-#define PS2_INT_OFF() do {      \
-    PCMSK2 &= ~(1<<PCINT20);    \
-    PCICR  &= ~(1<<PCIE2);      \
-} while (0)
-#define PS2_INT_VECT    PCINT2_vect
-#endif
-
-#endif
-
 #endif

diff --git a/hhkb/doc/HHKB_TP1684.jpg b/hhkb/doc/HHKB_TP1684.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/HHKB_chart1.jpg b/hhkb/doc/HHKB_chart1.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/HHKB_chart2.jpg b/hhkb/doc/HHKB_chart2.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/HHKB_connector.jpg b/hhkb/doc/HHKB_connector.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/HHKB_controller.jpg b/hhkb/doc/HHKB_controller.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/HHKB_keyswitch.jpg b/hhkb/doc/HHKB_keyswitch.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/connector_contact.jpg b/hhkb/doc/connector_contact.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/logic_analyzer.jpg b/hhkb/doc/logic_analyzer.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/probe_contact.jpg b/hhkb/doc/probe_contact.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/teensy_install.jpg b/hhkb/doc/teensy_install.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/hhkb/doc/teensy_wiring.jpg b/hhkb/doc/teensy_wiring.jpg
old mode 100755 (executable)
new mode 100644 (file)

diff --git a/macway/Makefile b/macway/Makefile
index c603ca7b98540d30520347b4d8146749240fe854..6e7fa7fd9f3c6c028be7b5d1b2641bc0dd26a36a 100644 (file)
--- a/macway/Makefile
+++ b/macway/Makefile
@@ -37,13 +37,13 @@ F_CPU = 16000000
 #
 MOUSEKEY_ENABLE = yes  # Mouse keys
 #PS2_MOUSE_ENABLE = yes        # PS/2 mouse(TrackPoint) support
-USB_EXTRA_ENABLE = yes # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 #USB_NKRO_ENABLE = yes # USB Nkey Rollover
 
 
 
 #---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli.exe -mmcu=$(MCU) -w -v $(TARGET).hex
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
 
 
 

diff --git a/ps2_usb/Makefile b/ps2_usb/Makefile
old mode 100755 (executable)
new mode 100644 (file)
index 6059629..a548b56
--- a/ps2_usb/Makefile
+++ b/ps2_usb/Makefile
@@ -1,5 +1,10 @@
+#
+# Makefile for PJRC Teensy
+#
+
+
 # Target file name (without extension).
-TARGET = ps2_usb
+TARGET = ps2_usb_pjrc
 
 # Directory common source filess exist
 COMMON_DIR = ..
@@ -37,7 +42,7 @@ F_CPU = 16000000
 #   comment out to disable the options.
 #
 MOUSEKEY_ENABLE = yes  # Mouse keys
-USB_EXTRA_ENABLE = yes # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 USB_NKRO_ENABLE = yes  # USB Nkey Rollover
 
 

diff --git a/ps2_usb/Makefile.vusb b/ps2_usb/Makefile.vusb
index 6e49fc44ddd4248716b988a6407666984a9208c9..ff86d7998ad642d1c56f98939aed78185103511d 100644 (file)
--- a/ps2_usb/Makefile.vusb
+++ b/ps2_usb/Makefile.vusb
@@ -1,5 +1,10 @@
+#
+# Makefile for V-USB
+#
+
+
 # Target file name (without extension).
-TARGET = ps2_vusb
+TARGET = ps2_usb_vusb
 
 # Directory common source filess exist
 COMMON_DIR = ..
@@ -43,7 +48,7 @@ F_CPU = 20000000
 #   comment out to disable the options.
 #
 MOUSEKEY_ENABLE = yes  # Mouse keys
-#USB_EXTRA_ENABLE = yes        # Enhanced feature for Windows(Audio control and System control)
+USB_EXTRA_ENABLE = yes # Audio control and System control
 #USB_NKRO_ENABLE = yes # USB Nkey Rollover