From: tmk Date: Wed, 8 Apr 2020 08:48:20 +0000 (+0900) Subject: sun_usb: Update README and rename to .md X-Git-Url: https://git.friedersdorff.com/?a=commitdiff_plain;h=05c2df1237d9539808cb2dd8eda0d445485f2812;p=max%2Ftmk_keyboard.git sun_usb: Update README and rename to .md --- diff --git a/converter/sun_usb/README b/converter/sun_usb/README.md similarity index 59% rename from converter/sun_usb/README rename to converter/sun_usb/README.md index 405a86ba..e65e2bcd 100644 --- a/converter/sun_usb/README +++ b/converter/sun_usb/README.md @@ -1,30 +1,31 @@ Sun to USB keyboard protocol converter ====================================== -Target MCU is ATMega32u4 but other USB capable AVR will also work. +Target MCU is ATMega32u2/4 but other USB capable AVR will also work. This converter will work with Sun Type 2-5 Keyboards. -Tested on: -Sun Type 3 Keyboard: http://blog.daveastels.com.s3-website-us-west-2.amazonaws.com/2014/12/27/type-3-keyboard.html -CTCSP SHORT TYPE KEYBOARD(Type 5): http://imgur.com/a/QIv6p +Check wiki pages for other information about TMK keyobard firware. +https://github.com/tmk/tmk_keyboard/wiki -Keymap of Type 3(keymap_sun3.c) were impoted from dastels's repository. -https://github.com/dastels/tmk_keyboard/tree/master/converter/sun3_usb +Update +------ +2020-04-08 Added unimap support Connector --------- - 8Pin mini DIN - ___ ___ - / |_| \ - / 8 7 6 \ - | 5 4 3 | - \_ 2 1 _/ - \_____/ - (receptacle) +Modern Type 4 and 5 keyboards uses 8Pin mini DIN. + + ___ ___ + / |_| \ + / 8 7 6 \ + | 5 4 3 | + \_ 2 1 _/ + \_____/ + (receptacle) Wiring: Pin mini DIN MCU @@ -42,18 +43,19 @@ Connector Protocol -------- Signal: Asynchronous, Negative logic, 1200baud, No Flow control + Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit - AVR USART engine expects positive logic while Sun keyboard signal is negative. - To use AVR UART engine you need external inverter in front of RX and TX pin. - Otherwise you can software serial routine to communicate the keyboard. +AVR USART engine expects positive logic while Sun keyboard signal is negative. +To use AVR UART engine you need external inverter in front of RX and TX pin. +Otherwise you can use software serial to communicate the keyboard. + +This firmware uses software serial by default, so you don't need any inverter. +It can be still built with 'make HARDWARE_SERIAL=y' to enable hardware serial if you have inverter. You can use 74LS04 for example. -This converter uses software method by default, so you don't need any inverter part. But -it can also be built with 'make HARDWARE_SERIAL=y' to enable hardware serial if there -is an inverter present. Good results have been obtained using a 74LS04 and hardware serial. +### Commands From System To Keyboard -Commands From System To Keyboard 0x01 Reset Keyboard responds with following byte sequence: Success: 0xFF 0x04 0x7F @@ -69,27 +71,29 @@ Commands From System To Keyboard 0x0F Layout Keyboard responds with 'Layout Response' 0xFE 0xXX -Commands From Keyboard To System +### Commands From Keyboard To System 0x7F Idle means no keys pressed. 0xFE Layout Response 0xFF Reset Response(followed by 0x04) -Reference - http://kentie.net/article/sunkbd/page2.htm - http://kentie.net/article/sunkbd/KBD.pdf +### Reference +- http://kentie.net/article/sunkbd/page2.htm +- http://kentie.net/article/sunkbd/KBD.pdf Build Firmware -------------- Just use 'make' + $ cd sun_usb $ make + Then, load the binary to MCU with your favorite programmer. -Sun commands ------------- +Keyboard Control +---------------- You can send Sun protocol commands with TMK `Magic` key combo. By default `Magic` key is `LShift` + `RShift`, `LAlt` + `RAlt' or `LMeta` + `RMeta`. https://github.com/tmk/tmk_keyboard#magic-commands @@ -106,3 +110,12 @@ PgDown: LED all On Insert: Layout Delete: Reset ``` + + +Tested on +--------- +### Type 3 +http://blog.daveastels.com.s3-website-us-west-2.amazonaws.com/2014/12/27/type-3-keyboard.html + +### CTCSP SHORT TYPE KEYBOARD(Type 5) +http://imgur.com/a/QIv6p