From: tmk <hasu@tmk-kbd.com>
Date: Sat, 8 Sep 2018 00:34:50 +0000 (+0900)
Subject: pc98_usb: Add ATMega32u4 support
X-Git-Url: https://git.friedersdorff.com/?a=commitdiff_plain;h=f57b7b9087fbded607883a372a3acbb811a622da;p=max%2Ftmk_keyboard.git

pc98_usb: Add ATMega32u4 support
---

diff --git a/converter/pc98_usb/Makefile b/converter/pc98_usb/Makefile
index 24606d69..a3cf2a29 100644
--- a/converter/pc98_usb/Makefile
+++ b/converter/pc98_usb/Makefile
@@ -1,29 +1,25 @@
 # Target file name (without extension).
-TARGET = pc98_usb
+TARGET ?= pc98_usb
 
 # Directory common source filess exist
-TMK_DIR = ../../tmk_core
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
 # keyboard dependent files
 #   Add one of lines below to select serial protocol implementation
 #	protocol/serial_uart.c
 #	protocol/serial_soft.c
-SRC =	matrix.c \
+SRC ?=	matrix.c \
 	protocol/serial_uart.c
 
-CONFIG_H = config.h
+CONFIG_H ?= config.h
 
 
 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-#MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-MCU = atmega32u2       # TMK Converter
+MCU ?= atmega32u2       # TMK Converter
 
 
 # Processor frequency.
@@ -31,14 +27,14 @@ MCU = atmega32u2       # TMK Converter
 #   so your program will run at the correct speed.  You should also set this
 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
 #   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
+F_CPU ?= 16000000
 
 
 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
+ARCH ?= AVR8
 
 # Input clock frequency.
 #     This will define a symbol, F_USB, in all source code files equal to the
@@ -51,7 +47,7 @@ ARCH = AVR8
 #
 #     If no clock division is performed on the input clock inside the AVR (via the
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
+F_USB ?= $(F_CPU)
 
 # Interrupt driven control endpoint task
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
@@ -60,12 +56,12 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 # Build Options
 #   *Comment out* to disable the options.
 #
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-CONSOLE_ENABLE = yes	# Console for debug
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#NKRO_ENABLE = yes	# USB Nkey Rollover
-UNIMAP_ENABLE = yes
+MOUSEKEY_ENABLE ?= yes	# Mouse keys
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control
+CONSOLE_ENABLE ?= yes	# Console for debug
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+#NKRO_ENABLE ?= yes	# USB Nkey Rollover
+UNIMAP_ENABLE ?= yes
 
 
 # Boot Section Size in bytes
diff --git a/converter/pc98_usb/README b/converter/pc98_usb/README
index 6da54178..24200d83 100644
--- a/converter/pc98_usb/README
+++ b/converter/pc98_usb/README
@@ -42,7 +42,7 @@ Frame format: 1-Start bit(Lo), 8-Data bits, Odd-Parity, 1-Stop bit
 
 Build Firmware
 --------------
-Just use 'make' to bild firmware
+Just use 'make' to bild firmware for TMK PC98 converter.
 
     $ make clean
     $ make
@@ -53,6 +53,12 @@ To flash firmware
 
 then push button on converter to flash firmware.
 
+If you are using ATMega32u4 based board instead of premade TMK PC98 converter(ATMega32u2) use following commands.
+
+    $ make -f Makefile.32u4 clean
+    $ make -f Makefile.32u4
+    $ make -f Makefile.32u4 dfu
+
 
 
 PC98 Scan Codes