From 39da065913380c89246e6f788e1be772947c470e Mon Sep 17 00:00:00 2001 From: Oleg Kostyuk Date: Mon, 9 Sep 2013 01:30:44 +0300 Subject: [PATCH] Converting files to Unix-like format --- keyboard/ergodox/i2cmaster.h | 356 +++++++++++++++--------------- keyboard/ergodox/twimaster.c | 404 +++++++++++++++++------------------ 2 files changed, 380 insertions(+), 380 deletions(-) diff --git a/keyboard/ergodox/i2cmaster.h b/keyboard/ergodox/i2cmaster.h index 70f51fd3..3917b9e6 100644 --- a/keyboard/ergodox/i2cmaster.h +++ b/keyboard/ergodox/i2cmaster.h @@ -1,178 +1,178 @@ -#ifndef _I2CMASTER_H -#define _I2CMASTER_H 1 -/************************************************************************* -* Title: C include file for the I2C master interface -* (i2cmaster.S or twimaster.c) -* Author: Peter Fleury http://jump.to/fleury -* File: $Id: i2cmaster.h,v 1.10 2005/03/06 22:39:57 Peter Exp $ -* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3 -* Target: any AVR device -* Usage: see Doxygen manual -**************************************************************************/ - -#ifdef DOXYGEN -/** - @defgroup pfleury_ic2master I2C Master library - @code #include @endcode - - @brief I2C (TWI) Master Software Library - - Basic routines for communicating with I2C slave devices. This single master - implementation is limited to one bus master on the I2C bus. - - This I2c library is implemented as a compact assembler software implementation of the I2C protocol - which runs on any AVR (i2cmaster.S) and as a TWI hardware interface for all AVR with built-in TWI hardware (twimaster.c). - Since the API for these two implementations is exactly the same, an application can be linked either against the - software I2C implementation or the hardware I2C implementation. - - Use 4.7k pull-up resistor on the SDA and SCL pin. - - Adapt the SCL and SDA port and pin definitions and eventually the delay routine in the module - i2cmaster.S to your target when using the software I2C implementation ! - - Adjust the CPU clock frequence F_CPU in twimaster.c or in the Makfile when using the TWI hardware implementaion. - - @note - The module i2cmaster.S is based on the Atmel Application Note AVR300, corrected and adapted - to GNU assembler and AVR-GCC C call interface. - Replaced the incorrect quarter period delays found in AVR300 with - half period delays. - - @author Peter Fleury pfleury@gmx.ch http://jump.to/fleury - - @par API Usage Example - The following code shows typical usage of this library, see example test_i2cmaster.c - - @code - - #include - - - #define Dev24C02 0xA2 // device address of EEPROM 24C02, see datasheet - - int main(void) - { - unsigned char ret; - - i2c_init(); // initialize I2C library - - // write 0x75 to EEPROM address 5 (Byte Write) - i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode - i2c_write(0x05); // write address = 5 - i2c_write(0x75); // write value 0x75 to EEPROM - i2c_stop(); // set stop conditon = release bus - - - // read previously written value back from EEPROM address 5 - i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode - - i2c_write(0x05); // write address = 5 - i2c_rep_start(Dev24C02+I2C_READ); // set device address and read mode - - ret = i2c_readNak(); // read one byte from EEPROM - i2c_stop(); - - for(;;); - } - @endcode - -*/ -#endif /* DOXYGEN */ - -/**@{*/ - -#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304 -#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !" -#endif - -#include - -/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */ -#define I2C_READ 1 - -/** defines the data direction (writing to I2C device) in i2c_start(),i2c_rep_start() */ -#define I2C_WRITE 0 - - -/** - @brief initialize the I2C master interace. Need to be called only once - @param void - @return none - */ -extern void i2c_init(void); - - -/** - @brief Terminates the data transfer and releases the I2C bus - @param void - @return none - */ -extern void i2c_stop(void); - - -/** - @brief Issues a start condition and sends address and transfer direction - - @param addr address and transfer direction of I2C device - @retval 0 device accessible - @retval 1 failed to access device - */ -extern unsigned char i2c_start(unsigned char addr); - - -/** - @brief Issues a repeated start condition and sends address and transfer direction - - @param addr address and transfer direction of I2C device - @retval 0 device accessible - @retval 1 failed to access device - */ -extern unsigned char i2c_rep_start(unsigned char addr); - - -/** - @brief Issues a start condition and sends address and transfer direction - - If device is busy, use ack polling to wait until device ready - @param addr address and transfer direction of I2C device - @return none - */ -extern void i2c_start_wait(unsigned char addr); - - -/** - @brief Send one byte to I2C device - @param data byte to be transfered - @retval 0 write successful - @retval 1 write failed - */ -extern unsigned char i2c_write(unsigned char data); - - -/** - @brief read one byte from the I2C device, request more data from device - @return byte read from I2C device - */ -extern unsigned char i2c_readAck(void); - -/** - @brief read one byte from the I2C device, read is followed by a stop condition - @return byte read from I2C device - */ -extern unsigned char i2c_readNak(void); - -/** - @brief read one byte from the I2C device - - Implemented as a macro, which calls either i2c_readAck or i2c_readNak - - @param ack 1 send ack, request more data from device
- 0 send nak, read is followed by a stop condition - @return byte read from I2C device - */ -extern unsigned char i2c_read(unsigned char ack); -#define i2c_read(ack) (ack) ? i2c_readAck() : i2c_readNak(); - - -/**@}*/ -#endif +#ifndef _I2CMASTER_H +#define _I2CMASTER_H 1 +/************************************************************************* +* Title: C include file for the I2C master interface +* (i2cmaster.S or twimaster.c) +* Author: Peter Fleury http://jump.to/fleury +* File: $Id: i2cmaster.h,v 1.10 2005/03/06 22:39:57 Peter Exp $ +* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3 +* Target: any AVR device +* Usage: see Doxygen manual +**************************************************************************/ + +#ifdef DOXYGEN +/** + @defgroup pfleury_ic2master I2C Master library + @code #include @endcode + + @brief I2C (TWI) Master Software Library + + Basic routines for communicating with I2C slave devices. This single master + implementation is limited to one bus master on the I2C bus. + + This I2c library is implemented as a compact assembler software implementation of the I2C protocol + which runs on any AVR (i2cmaster.S) and as a TWI hardware interface for all AVR with built-in TWI hardware (twimaster.c). + Since the API for these two implementations is exactly the same, an application can be linked either against the + software I2C implementation or the hardware I2C implementation. + + Use 4.7k pull-up resistor on the SDA and SCL pin. + + Adapt the SCL and SDA port and pin definitions and eventually the delay routine in the module + i2cmaster.S to your target when using the software I2C implementation ! + + Adjust the CPU clock frequence F_CPU in twimaster.c or in the Makfile when using the TWI hardware implementaion. + + @note + The module i2cmaster.S is based on the Atmel Application Note AVR300, corrected and adapted + to GNU assembler and AVR-GCC C call interface. + Replaced the incorrect quarter period delays found in AVR300 with + half period delays. + + @author Peter Fleury pfleury@gmx.ch http://jump.to/fleury + + @par API Usage Example + The following code shows typical usage of this library, see example test_i2cmaster.c + + @code + + #include + + + #define Dev24C02 0xA2 // device address of EEPROM 24C02, see datasheet + + int main(void) + { + unsigned char ret; + + i2c_init(); // initialize I2C library + + // write 0x75 to EEPROM address 5 (Byte Write) + i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode + i2c_write(0x05); // write address = 5 + i2c_write(0x75); // write value 0x75 to EEPROM + i2c_stop(); // set stop conditon = release bus + + + // read previously written value back from EEPROM address 5 + i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode + + i2c_write(0x05); // write address = 5 + i2c_rep_start(Dev24C02+I2C_READ); // set device address and read mode + + ret = i2c_readNak(); // read one byte from EEPROM + i2c_stop(); + + for(;;); + } + @endcode + +*/ +#endif /* DOXYGEN */ + +/**@{*/ + +#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304 +#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !" +#endif + +#include + +/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */ +#define I2C_READ 1 + +/** defines the data direction (writing to I2C device) in i2c_start(),i2c_rep_start() */ +#define I2C_WRITE 0 + + +/** + @brief initialize the I2C master interace. Need to be called only once + @param void + @return none + */ +extern void i2c_init(void); + + +/** + @brief Terminates the data transfer and releases the I2C bus + @param void + @return none + */ +extern void i2c_stop(void); + + +/** + @brief Issues a start condition and sends address and transfer direction + + @param addr address and transfer direction of I2C device + @retval 0 device accessible + @retval 1 failed to access device + */ +extern unsigned char i2c_start(unsigned char addr); + + +/** + @brief Issues a repeated start condition and sends address and transfer direction + + @param addr address and transfer direction of I2C device + @retval 0 device accessible + @retval 1 failed to access device + */ +extern unsigned char i2c_rep_start(unsigned char addr); + + +/** + @brief Issues a start condition and sends address and transfer direction + + If device is busy, use ack polling to wait until device ready + @param addr address and transfer direction of I2C device + @return none + */ +extern void i2c_start_wait(unsigned char addr); + + +/** + @brief Send one byte to I2C device + @param data byte to be transfered + @retval 0 write successful + @retval 1 write failed + */ +extern unsigned char i2c_write(unsigned char data); + + +/** + @brief read one byte from the I2C device, request more data from device + @return byte read from I2C device + */ +extern unsigned char i2c_readAck(void); + +/** + @brief read one byte from the I2C device, read is followed by a stop condition + @return byte read from I2C device + */ +extern unsigned char i2c_readNak(void); + +/** + @brief read one byte from the I2C device + + Implemented as a macro, which calls either i2c_readAck or i2c_readNak + + @param ack 1 send ack, request more data from device
+ 0 send nak, read is followed by a stop condition + @return byte read from I2C device + */ +extern unsigned char i2c_read(unsigned char ack); +#define i2c_read(ack) (ack) ? i2c_readAck() : i2c_readNak(); + + +/**@}*/ +#endif diff --git a/keyboard/ergodox/twimaster.c b/keyboard/ergodox/twimaster.c index f0d850c2..a4dc5c11 100644 --- a/keyboard/ergodox/twimaster.c +++ b/keyboard/ergodox/twimaster.c @@ -1,202 +1,202 @@ -/************************************************************************* -* Title: I2C master library using hardware TWI interface -* Author: Peter Fleury http://jump.to/fleury -* File: $Id: twimaster.c,v 1.3 2005/07/02 11:14:21 Peter Exp $ -* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3 -* Target: any AVR device with hardware TWI -* Usage: API compatible with I2C Software Library i2cmaster.h -**************************************************************************/ -#include -#include - -#include - - -/* define CPU frequency in Mhz here if not defined in Makefile */ -#ifndef F_CPU -#define F_CPU 4000000UL -#endif - -/* I2C clock in Hz */ -#define SCL_CLOCK 100000L - - -/************************************************************************* - Initialization of the I2C bus interface. Need to be called only once -*************************************************************************/ -void i2c_init(void) -{ - /* initialize TWI clock: 100 kHz clock, TWPS = 0 => prescaler = 1 */ - - TWSR = 0; /* no prescaler */ - TWBR = ((F_CPU/SCL_CLOCK)-16)/2; /* must be > 10 for stable operation */ - -}/* i2c_init */ - - -/************************************************************************* - Issues a start condition and sends address and transfer direction. - return 0 = device accessible, 1= failed to access device -*************************************************************************/ -unsigned char i2c_start(unsigned char address) -{ - uint8_t twst; - - // send START condition - TWCR = (1< http://jump.to/fleury +* File: $Id: twimaster.c,v 1.3 2005/07/02 11:14:21 Peter Exp $ +* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3 +* Target: any AVR device with hardware TWI +* Usage: API compatible with I2C Software Library i2cmaster.h +**************************************************************************/ +#include +#include + +#include + + +/* define CPU frequency in Mhz here if not defined in Makefile */ +#ifndef F_CPU +#define F_CPU 4000000UL +#endif + +/* I2C clock in Hz */ +#define SCL_CLOCK 100000L + + +/************************************************************************* + Initialization of the I2C bus interface. Need to be called only once +*************************************************************************/ +void i2c_init(void) +{ + /* initialize TWI clock: 100 kHz clock, TWPS = 0 => prescaler = 1 */ + + TWSR = 0; /* no prescaler */ + TWBR = ((F_CPU/SCL_CLOCK)-16)/2; /* must be > 10 for stable operation */ + +}/* i2c_init */ + + +/************************************************************************* + Issues a start condition and sends address and transfer direction. + return 0 = device accessible, 1= failed to access device +*************************************************************************/ +unsigned char i2c_start(unsigned char address) +{ + uint8_t twst; + + // send START condition + TWCR = (1<