From f57b7b9087fbded607883a372a3acbb811a622da Mon Sep 17 00:00:00 2001 From: tmk Date: Sat, 8 Sep 2018 09:34:50 +0900 Subject: [PATCH] pc98_usb: Add ATMega32u4 support --- converter/pc98_usb/Makefile | 34 +++++++++++++++------------------- converter/pc98_usb/README | 8 +++++++- 2 files changed, 22 insertions(+), 20 deletions(-) diff --git a/converter/pc98_usb/Makefile b/converter/pc98_usb/Makefile index 24606d69..a3cf2a29 100644 --- a/converter/pc98_usb/Makefile +++ b/converter/pc98_usb/Makefile @@ -1,29 +1,25 @@ # Target file name (without extension). -TARGET = pc98_usb +TARGET ?= pc98_usb # Directory common source filess exist -TMK_DIR = ../../tmk_core +TMK_DIR ?= ../../tmk_core # Directory keyboard dependent files exist -TARGET_DIR = . +TARGET_DIR ?= . # keyboard dependent files # Add one of lines below to select serial protocol implementation # protocol/serial_uart.c # protocol/serial_soft.c -SRC = matrix.c \ +SRC ?= matrix.c \ protocol/serial_uart.c -CONFIG_H = config.h +CONFIG_H ?= config.h # MCU name, you MUST set this to match the board you are using # type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -#MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 -MCU = atmega32u2 # TMK Converter +MCU ?= atmega32u2 # TMK Converter # Processor frequency. @@ -31,14 +27,14 @@ MCU = atmega32u2 # TMK Converter # so your program will run at the correct speed. You should also set this # variable to same clock speed. The _delay_ms() macro uses this, and many # examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 +F_CPU ?= 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). -ARCH = AVR8 +ARCH ?= AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the @@ -51,7 +47,7 @@ ARCH = AVR8 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) +F_USB ?= $(F_CPU) # Interrupt driven control endpoint task OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT @@ -60,12 +56,12 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Build Options # *Comment out* to disable the options. # -MOUSEKEY_ENABLE = yes # Mouse keys -EXTRAKEY_ENABLE = yes # Audio control and System control -CONSOLE_ENABLE = yes # Console for debug -COMMAND_ENABLE = yes # Commands for debug and configuration -#NKRO_ENABLE = yes # USB Nkey Rollover -UNIMAP_ENABLE = yes +MOUSEKEY_ENABLE ?= yes # Mouse keys +EXTRAKEY_ENABLE ?= yes # Audio control and System control +CONSOLE_ENABLE ?= yes # Console for debug +COMMAND_ENABLE ?= yes # Commands for debug and configuration +#NKRO_ENABLE ?= yes # USB Nkey Rollover +UNIMAP_ENABLE ?= yes # Boot Section Size in bytes diff --git a/converter/pc98_usb/README b/converter/pc98_usb/README index 6da54178..24200d83 100644 --- a/converter/pc98_usb/README +++ b/converter/pc98_usb/README @@ -42,7 +42,7 @@ Frame format: 1-Start bit(Lo), 8-Data bits, Odd-Parity, 1-Stop bit Build Firmware -------------- -Just use 'make' to bild firmware +Just use 'make' to bild firmware for TMK PC98 converter. $ make clean $ make @@ -53,6 +53,12 @@ To flash firmware then push button on converter to flash firmware. +If you are using ATMega32u4 based board instead of premade TMK PC98 converter(ATMega32u2) use following commands. + + $ make -f Makefile.32u4 clean + $ make -f Makefile.32u4 + $ make -f Makefile.32u4 dfu + PC98 Scan Codes -- 2.45.2